Menu
EUR
Techniek Totaal Logo

We are closed today

Dear visitor!

Welcome to our site. Today is Sunday, a day of rest in the Christian religion. Therefore, we have chosen not to work today, and our webshop is closed. Of course, you are warmly welcome again tomorrow.

Have a nice Sunday and best regards,
Team Techniek Totaal

Tractor parts Fendt Farmer 308 (Typ 178)

Looking for parts for your Fendt Farmer 308 (Typ 178) tractor? In this category, you'll find everything you need for the maintenance and repair of your vehicle.

1063 parts found for Fendt Farmer 308 (Typ 178)
Show:
Stabilus Gas strut door 100 N, 500 mm, stroke 203 mm Fendt
Stabilus
To fit as: Fendt Door More
To fit as: Fendt Door
€31,92 €26,38 €31,28 €25,85
You save 2%
GRANIT Valve guide Renault AKD 311Z
GRANIT
Engine types: AKD 311Z More
Engine types: AKD 311Z
€19,90 €16,45 €18,82 €15,55
You save 5%
GRANIT Intake/exhaust manifold gasket MWM AKD 112, KD 110.5, D208.3, AKD311Z
GRANIT
Engine types: MWM AKD 112, KD 110.5, D 208.3, AKD 311 Z More
Engine types: MWM AKD 112, KD 110.5, D 208.3, AKD 311 Z
€6,29 €5,20
GRANIT Compression spring hand brake lever Fendt
GRANIT
To fit as: Fendt FL 120, FW 120, FW 216, FL 131, F 12 GH, F 12 HL, F 12 GT, F 220 GT, F 225 GT, F 230 GT, F 231 GT, F 15, F 17, F 20, F 24, FL 236, FW... More
To fit as: Fendt FL 120, FW 120, FW 216, FL 131, F 12 GH, F 12 HL, F 1...
€7,80 €6,45 €7,64 €6,31
You save 2%
GRANIT Return spring for brake shoe Ø 10 mm, length 83 mm Deutz 3006-6206
GRANIT
To fit as: Deutz 3006, 4006, 5206, 6206 More
To fit as: Deutz 3006, 4006, 5206, 6206
€5,18 €4,28 €3,76 €3,11
You save 27%
GRANIT Drive shaft Fendt Farmer 305 - 310
€1.132,19 €935,69
ZF Inner plate front axle 4468054022 Ø 72 x 44 mm, 1,5 mm Case IH, Fendt
ZF
Außen-Ø (mm): 72 Stärke: 1,5 Innen-Ø: 44 | Reference no.: 4131.303.005 More
Außen-Ø (mm): 72 Stärke: 1,5 Innen-Ø: 44 | Reference no.: 4131.303
€107,51 €88,85
LUK Clutch kit Ø 320 mm with thrust bearing and pilot bearing Fendt Farmer 303 - 310
LUK
Contents: Single clutch, clutch plate, release bearing and guide bearing More
Contents: Single clutch, clutch plate, release bearing and guide beari...
€1.438,07 €1.188,49 €1.405,99 €1.161,98
You save 2%
GRANIT Service kit Fendt Farmer 305 - 310, 1000 - 9000 operating hours
GRANIT
Set consisting of: 1x cab filter 1x feed pump repair set 1x sealing ring 1x engine oil filter 4x valve cover gasket 2x fuel filter 1x hydraulic filter... More
Set consisting of: 1x cab filter 1x feed pump repair set 1x sealing ri...
€278,81 €230,42
GRANIT Main bearing, standard Ø 70 mm Fendt Farmer 102 - 312, GT 231
€28,50 €23,55 €27,86 €23,02
You save 2%
Wabco Pressure relief valve 20 bar, inschakeldruk 16 bar, M16 x 1,5
Wabco
Operating pressure max. (bar): 20 | Fixing: Hole Ø 8.2 x 57 mm | Opening pressure (bar): p2 + 2,5 | Output pressure (bar): 7,4 + 0,2 | Inlet connecti... More
Operating pressure max. (bar): 20 | Fixing: Hole Ø 8.2 x 57 mm | Open...
€250,81 €207,28
Wabco Trailer control valve with drukbegrenzing 8 bar, M22 x 1,5, NW 10 mm
Wabco
Connection: M22 x 1.5 | To fit: Mercedes and others | Nominal width (mm): 10 | Working pressure (bar): 8 More
Connection: M22 x 1.5 | To fit: Mercedes and others | Nominal width (m...
€553,48 €457,42
Wabco Trailer control valve brake fluid 5 bar, final pressure 15 bar, 2,2 m³
Wabco
Displacement (m³): 2,2 | End pressure (bar): 15 | Set pressure (bar): 5 More
Displacement (m³): 2,2 | End pressure (bar): 15 | Set pressure (bar):...
€1.919,01 €1.585,96
Wabco Repair set compressor M26 x 1,5 Fendt, John Deere
Wabco
To fit: 411 141 500 0, 411 141 640 0/7, 411 141 711 0, 411 141 713 0 | Connection (mm): M26 x 1,5 | Connection: M26 x 1.5 More
To fit: 411 141 500 0, 411 141 640 0/7, 411 141 711 0, 411 141 713 0 |...
€147,53 €121,93
GRANIT Internal plate PTO shaft sinus plate 2,5 mm, 80,5 mm, 140 mm Fendt
GRANIT
Version: thickness = 2,5 mm inner = 80,5 mm outer = 140 mm More
Version: thickness = 2,5 mm inner = 80,5 mm outer = 140 mm
€43,64 €36,07
GRANIT Internal plate PTO shaft 3 mm, 80,5 mm, 140 mm Fendt
GRANIT
Version: thickness = 3 mm inner = 80,5 mm outer = 140 mm More
Version: thickness = 3 mm inner = 80,5 mm outer = 140 mm
€36,73 €30,36
GRANIT Repair set clutch cylinder with piston Fendt Farmer 303 - 309
GRANIT
Menke no.: 209829 | Additional information: with piston More
Menke no.: 209829 | Additional information: with piston
€132,08 €109,16
GRANIT External plate 3,5 mm, inner 115 mm, outer 181 mm Fendt
GRANIT
Version: Thickness: 3.5 mm Inner: 115 mm Outer: 181 mm More
Version: Thickness: 3.5 mm Inner: 115 mm Outer: 181 mm
€18,73 €15,48
GRANIT Expansion valve 3/8 - 1/2 inch o-ring Fendt, John Deere, Renault
GRANIT
Connection thread E: # 6, 3/8"" O-ring | Connection thread A: # 8, 1/2"" O-ring | Equipment: O-ring | Weight (g): 182 More
Connection thread E: # 6, 3/8"" O-ring | Connection thread A: # 8, 1/2...
€85,87 €70,97
GRANIT Alternator 14 V / 120 A, flange 56 mm
GRANIT
Additional information: With W connection | Nominal values (V / A): 14 / 120 | Pulley Ø (mm): - | Mounting L / d / R (mm): 56,0 / 8,2 / 85,0 | Pulley... More
Additional information: With W connection | Nominal values (V / A): 14...
€176,65 €145,99
Showing 505 - 528 of 1063

Fendt Farmer 308 (Typ 178) specs

The Fendt Farmer 308 with type designation Typ 178 covers the 308 LS and 308 LSA from the Farmer 300 series, built from 1980 to 2000. The "LS" indicates a higher specification level, while the "A" in LSA refers to all-wheel drive. The Typ 178 is therefore the LS/LSA line of the Farmer 308, distinct from the later compact C line (Typ 118). Over the twenty years of production, several revisions were carried out, gradually improving both power output and transmission.

Engine

Power comes from an MWM D 226.4.2, a water-cooled four-stroke four-cylinder inline engine with direct injection, overhead valves, pressure lubrication, inline injection pump (Bosch PES 4 A 80 D 320/3 RS 1301), multi-hole injector nozzles, centrifugal governor and dry cylinder liners. Cooling is handled by a thermostatically controlled dual-circuit system. Displacement is 4.2 litres (bore x stroke: 105 x 120 mm), rated engine speed is 2,400 rpm. Maximum torque was initially 275 Nm at 1,498 rpm.

From 1989 the turbocharged MWM TD 226 B-4 was used (rated speed 2,250 rpm, 26% torque increase). Power rose from 78 hp (1980) to 82 hp in 1989 and further to 86 hp (approx. 63 kW) in 1991. Maximum torque increased from 321 Nm at 1,550 rpm (1989) to 337 Nm at 1,550 rpm (1991). From approximately the 1989 model year, wet cylinder liners were used.

Transmission and travel speeds

The 308 LS and 308 LSA were delivered with a fully synchronised gearbox. The first generation had 15 forward and 4 reverse gears (15/4), with two overdrive speeds for 25/30 or 30/40 km/h. In 1984 this became a 21/6 gearbox, followed in 1991 by the optional 21/21 reverser transmission. Top speed is 30 km/h as standard, with an optional 40 km/h version. Shifting is handled via a Voith fluid coupling type 358 TD-F (from 1989: 360 TD-F2, from 1990: 360 TD-F1) and a Fichtel & Sachs single-disc dry clutch type GT NX 310 (from 1984: GTF 320 N or GTF 320 N-295).

The front axle of the LSA is a load-switchable ZF oscillating axle type APL-1552 (from 1984: APL-335, from 1989: APL-735, from 1990: APL-700 F3), with a lateral driveshaft and self-locking "Locomatik" differential.

Hydraulics and lift capacity

The hydraulic system is a Fendt block-type control hydraulic with mechanical lift control (MHR) and top link sensing. The three-point linkage is category II, available on request with a quick coupler. A single-acting working cylinder with an 86 mm bore and 137.4 mm stroke is fitted as standard; optionally two additional working cylinders with a 45 mm bore and 181 mm stroke.

  • Early pump flow: 39.95 l/min at 175 bar (as three-circuit system 66 l/min)
  • Max. early lift capacity: 3,490 kp / lift travel 660 mm
  • From 1984: 180 bar working pressure, max. lift capacity 3,820 kp
  • Later model: 71 l/min at 180 bar, max. lift capacity 4,420 kp
  • Optional front hydraulics (cat. II): two working cylinders 28 mm bore, 162 mm stroke, max. lift capacity 24.6 kN

PTO

The PTO is switchable to 540, 750 and 1,000 rpm. A ground-speed PTO is available on request (9.6 PTO revolutions per wheel revolution). Maximum permissible torque: 1,750 Nm at 540 rpm, 1,100 Nm at 750 rpm and 900 Nm at 1,000 rpm. From 1991, front and rear axle are electrohydraulically switchable.

Dimensions and weights

  • Length: approx. 4.0 m
  • Width: approx. 2.14 m
  • Height: approx. 2.7 m
  • Wheelbase: approx. 2.28 m
  • Unladen weight 308 LS: approx. 3,795 kg / permissible total weight: 6,500 kg
  • Unladen weight 308 LSA: approx. 3,870 kg / permissible total weight: 6,500 kg

Tyres and brakes

Standard tyre sizes are 13.6R24 front and 16.9R34 rear. The parking brake is an internal shoe brake on the differential output shafts. A single- or dual-circuit compressed air braking system was available as an option. At 40 km/h, drum brakes in the front wheels are mandatory; at 30 km/h they are optional.

Cab

The tractor comes with a sound-insulated comfort cab with a noise level of 73.5 dB(A), an air-suspended seat, tinted glass, adjustable front, side and rear windows and an opening roof hatch. Standard equipment includes heating with a three-speed blower, interior lighting, a radio pre-installation with two speakers, electrically adjustable exterior mirrors, digital instruments and rear work lights. Optional extras include air conditioning (later versions), front work lights, particulate filter and H4 supplementary front lighting.

Production numbers Typ 178

The 308 LS was built in the following series: T 178.010 (1980-1984, 2,633 units), T 178.011 (1984-1988, 596 units), T 178.050 (1989, 37 units), T 178.060 (1989-1990, 73 units), T 178.061 (1990-1991, 50 units), T 178.062/063/064 (1991-1993, 14/24/28 units) and T 178.065 (1993-1998, 206 units). The 308 LSA ran from T 178.210 (1980-1984, 5,498 units) and T 178.211 (1984-1988, 2,964 units) through to T 178.265 (1993-1998, 2,263 units).

Parts and brands for the Fendt Farmer 308 (Typ 178)

We stock a wide range of parts for the Fendt Farmer 308 Typ 178, including engine parts, filters, brake parts, hydraulic components, exhaust parts, electrical components and cab parts. We work with brands such as Granit, Agco Parts, Bosch, Hella, Mahle, Mann-Filter, Kramp, Grammer, Cobo, Scharmüller and Walterscheid, so there is always a choice between an original part or a well-fitting alternative.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart