Menu
EUR

Lindner Geotrac 60 tractor parts & technical data

This page holds more than 60 parts selected for the Lindner Geotrac 60. Choose from trailer couplings, electrics and parts for the brakes and transmission.

61 parts found for Lindner Geotrac 60
Show:
Scharmüller Ball 80® ball inserts gray cast iron, rail width 335 mm, 4000 kg
16%
Scharmüller
Ball 80® ball inserts gray cast iron, rail width 335 mm, 4000 kg
Rail width: 335 mm. Detent pin Ø: 22 mm. Guide width: 30 mm. Load capacity: 4000...
€1.221,12 €1.009,19 €1.028,50 €850,00
 
GRANIT Alternator 14 V, 70 A, flange 82 mm
5%
GRANIT
Alternator 14 V, 70 A, flange 82 mm
Form: A | Flange size (mm): 82,0 | Direction of rotation: ↻ | Installation angle...
€148,32 €122,58 €140,90 €116,45
 
GRANIT Alternator 14 V, 65 A, flange 86 mm, pulley Ø 71 mm
5%
GRANIT
Alternator 14 V, 65 A, flange 86 mm, pulley Ø 71 mm
Direction of rotation: ↻ | Mounting L / d / R (mm): 86,0 / 8,2 / 86,0 | Form: A ...
€146,49 €121,07 €139,15 €115,00
 
GRANIT Starter motor with reduction 12 V, 3,2 kW, 10 teeth, 226 mm, Ø 89 mm
5%
GRANIT
Starter motor with reduction 12 V, 3,2 kW, 10 teeth, 226 mm, Ø 89 mm
€287,67 €237,74 €273,25 €225,83
 
GRANIT Feed pump 4 bores, hole spacing 25 x 45 mm, flange 27 mm
5%
GRANIT
Feed pump 4 bores, hole spacing 25 x 45 mm, flange 27 mm
Version: 4 holes, Vertical hole spacing: 25 mm, Horizontal hole spacing: 45 mm, ...
€37,09 €30,65 €35,20 €29,09
 
Scharmüller Drawbar K80 manual, rail 325 mm, pin Ø 25 mm, 2000 kg, black
16%
Scharmüller
Drawbar K80 manual, rail 325 mm, pin Ø 25 mm, 2000 kg, black
Rail width: 325 mm. Detent pin Ø: 25 mm. Guide width: 26 mm. Load capacity: 2000...
€1.364,41 €1.127,61 €1.149,20 €949,75
 
Double clutch TGU 6290/280 45 x 50 mm, 24 splines Lindner
5%
Double clutch TGU 6290/280 45 x 50 mm, 24 splines Lindner
Dimensions (mm): 45 x 50, 24 grooves | Additional information: Made in Germany
€665,50 €550,00 €632,20 €522,48
 
Scharmüller Drawbar K80 manual, rail 335 mm, pin Ø 22 mm, 3000 kg, AGCO gray
16%
Scharmüller
Drawbar K80 manual, rail 335 mm, pin Ø 22 mm, 3000 kg, AGCO gray
Rail width: 335 mm. Detent pin Ø: 22 mm. Guide width: 30 mm. Load capacity: 3000...
€1.294,08 €1.069,49 €1.089,95 €900,79
 
LUK Clutch 45 x 50 mm, 24 grooves Lindner Geotrac 50 - 100
10%
LUK
Clutch 45 x 50 mm, 24 grooves Lindner Geotrac 50 - 100
Dimensions (mm): 45 x 50 24 Nuten
€990,86 €818,89 €896,45 €740,87
 
Clutch plate 290 28 x 32 mm, 17 splines, sintered Lindner
5%
Clutch plate 290 28 x 32 mm, 17 splines, sintered Lindner
Dimensions (mm): 28 x 32, 17 grooves | Material specifications: Sintered clutch ...
€264,02 €218,20 €250,80 €207,27
 
MAHLE Alternator 14 V, 100 A, flange 82 mm
38%
MAHLE
Alternator 14 V, 100 A, flange 82 mm
Nominal voltage (V): 14 | Additional information: Compact alternator, dust-tight...
€393,25 €325,00 €245,75 €203,10
 
LUK Connection set disc-Ø 300 mm Lindner Geotrac 50 - 100
10%
LUK
Connection set disc-Ø 300 mm Lindner Geotrac 50 - 100
Disc Ø (mm): 300 | To fit: Lindner | Contents: Kupplungsdruckplatte 230003111, K...
€1.387,76 €1.146,91 €1.255,55 €1.037,64
 
Showing 49 - 61 of 61

Hitching, filters and starting: Lindner Geotrac 60 parts

The Geotrac 60 is a compact Lindner that tends to work with a long list of implements. More than 60 parts on this page fit it, from Scharmüller, Walterscheid, Rockinger, Grammer and GRANIT.

Starting and charging

If your Geotrac 60 is slow to crank or the charge light stays on, there is a starter motor and an alternator for it here. Before swapping the starter, check battery voltage and go over the earth straps and terminals. A poor connection produces exactly the same symptoms as a tired starter.

Service filters

For routine servicing there are engine oil filters and fuel filters. Prime a new fuel filter with clean diesel where the design allows, then bleed the system at the bleed screw until only clear fuel with no bubbles comes out. Air left in the lines is a common reason an engine starts badly or stalls under load after a filter change.

On the oil filter, smear the rubber ring of the new filter with a little clean oil and tighten it by hand only. A filter done up with a wrench is a struggle to remove at the next service and the ring can be damaged. Run the engine briefly after the oil change, check the filter stays dry, then check the oil level again.

Hitching at the rear

  • Drawbars with a ball, and separate balls
  • A ball hitch and a top drawbar
  • Hitch jaws, including an automatic version
  • Piton Fix
  • Height adjustable adapter plates

Which system fits depends on the rail width and locking pin of the linkage already on the tractor, so measure those first.

An automatic hitch jaw catches the drawbar eye and locks itself, so you can couple up without leaving the seat. Check regularly that the pin drops fully home and keep the mechanism greased, because dirt and rust make the automatic action stick.

Clutch and seat

If the clutch slips under heavy work or only bites right at the top of the pedal, check the adjustment of the pedal first. When the plate really is worn, a new clutch plate for the Geotrac 60 is available. Look for oil on the old plate, because that points to a leaking seal that should be dealt with in the same job.

For the cab there are tractor seats, including an air suspended Grammer Maximo Professional.

Matching the part

The data plate confirms whether the tractor is a Geotrac 60. For filters, starter and alternator, the number on the old unit is the surest thing to compare with the product details. Other Geotrac models and the rest of the brand are found through the overview of Lindner parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart