Menu
EUR

Tractor parts Fendt Favorit 612 (Typ 383)

Looking for parts for your Fendt Favorit 612 (Typ 383) tractor? In this category, you'll find everything you need for the maintenance and repair of your vehicle.

546 parts found for Fendt Favorit 612 (Typ 383)
Show:
Radiator hose thermostat / water pump Ø 24 mm Fendt
8%
Radiator hose thermostat / water pump Ø 24 mm Fendt
Inner Ø: 24 mm.
€34,91 €28,85 €32,12 €26,54
 
Radiator hose thermostat Ø 34/38 mm Fendt Favorit 611-615
8%
Radiator hose thermostat Ø 34/38 mm Fendt Favorit 611-615
Inner Ø: 34 / 38 mm.
€46,50 €38,43 €42,78 €35,36
 
O-ring feed pump Fendt, Fiat
O-ring feed pump Fendt, Fiat
€3,59 €2,96
 
Connecting rod bolt Fendt, Renault
Connecting rod bolt Fendt, Renault
€39,13 €32,33
 
Cylinder head bolt M14 x 158 mm Case IH, Steyr, Fendt
8%
Cylinder head bolt M14 x 158 mm Case IH, Steyr, Fendt
Dimensions: M14 x 158 mm. Supplementary set: With thread at the top.
€47,30 €39,09 €43,52 €35,96
 
Hose lubricating pipe turbocharger Fendt
8%
Hose lubricating pipe turbocharger Fendt
€48,04 €39,70 €44,20 €36,53
 
Gasket exhaust Fendt Favorit 600-615
Gasket exhaust Fendt Favorit 600-615
€22,21 €18,36
 
Crankshaft seal rear outer-Ø 130 mm, inner-Ø 110 mm, width 13 mm
Crankshaft seal rear outer-Ø 130 mm, inner-Ø 110 mm, width 13 mm
Outer Ø: 130 mm. Width: 13 mm. Inner Ø: 110 mm.
€26,36 €21,79
 
Piston, complete Fendt Farmer 304-312, Favorit 509-615
8%
Piston, complete Fendt Farmer 304-312, Favorit 509-615
Menke no.: 208848.
€82,93 €68,54 €76,30 €63,05
 
Injection nozzle Fendt Farmer 309-310, Favorit 612-615
8%
Injection nozzle Fendt Farmer 309-310, Favorit 612-615
€41,29 €34,12 €37,99 €31,39
 
Set of parts feed pump Ø 29/35 mm, height 53 mm engine For 314
Set of parts feed pump Ø 29/35 mm, height 53 mm engine For 314
Dimensions: Ø 29/35 mm. Height: 53 mm.
€13,54 €11,19
 
Ball pin steel M6, wrench size 8, E 10 mm Fendt 7387MI, Xylon 524
Ball pin steel M6, wrench size 8, E 10 mm Fendt 7387MI, Xylon 524
A: M6 mm. SW: 8. E: 10 mm.
€5,78 €4,77
 
Bar three-point parts Fendt
Bar three-point parts Fendt
€31,11 €25,71
 
Guide ring Fendt
Guide ring Fendt
€19,54 €16,15
 
Angled screw lift arm M27 x 3 mm Fendt
8%
Angled screw lift arm M27 x 3 mm Fendt
Dimensions: Thread = M27 x 3 mm.
€80,43 €66,47 €74,00 €61,15
 
Adjusting nut for lower link strut M27 x 3 Fendt
8%
Adjusting nut for lower link strut M27 x 3 Fendt
Dimensions: Thread = M27 x 3 mm.
€58,94 €48,71 €54,22 €44,81
 
Pin for lifting strut top 25 x 110 mm Fendt Favorit 600-615
8%
Pin for lifting strut top 25 x 110 mm Fendt Favorit 600-615
Dimensions: 25 x 110 mm.
€33,70 €27,85 €31,00 €25,62
 
Gas strut roof window 120 N, 225 mm Fendt Farmer 240 S (Typ 294), GT 395
Gas strut roof window 120 N, 225 mm Fendt Farmer 240 S (Typ 294), GT 395
Newtons: 120. A: 225 mm. B: 130 mm. C: 6 mm. D: 6 mm. To fit: roof hatch. Form: ...
€31,20 €25,79
 
Spring driepuntcentrering Fendt
Spring driepuntcentrering Fendt
€21,80 €18,02
 
Spring plate fender Fendt
Spring plate fender Fendt
€12,28 €10,14
 
Scharmüller Drawbar frame 311/22/30, 2500 kg, Deutz-Fahr, Fendt
8%
Scharmüller
Drawbar frame 311/22/30, 2500 kg, Deutz-Fahr, Fendt
To fit as: Deutz-Fahr D-06 (10006-12006): 10006, 12006; Fendt Favorit 600 LS/LSA...
€1.458,18 €1.205,11 €1.341,53 €1.108,70
 
Cut-out switch starter motor solenoid switch 42 V, 0,5 A
Cut-out switch starter motor solenoid switch 42 V, 0,5 A
Version: Solenoid switch, 42 V / 0.5 A, With plug connection.
€35,83 €29,61
 
Temperature sender 6 - 24 V, M14 x 1,5, wrench size 19 mm, black
8%
Temperature sender 6 - 24 V, M14 x 1,5, wrench size 19 mm, black
Version: Connection type: 1 x 6.3 mm, Colour: black, Thread: M14 x 1.5, AF: 19.0...
€53,03 €43,83 €48,79 €40,32
 
Tank temperature gauge 12 volt
Tank temperature gauge 12 volt
Version: 12 V | To fit Fendt.
€1.093,42 €903,65
 
Push button switch fan 12 / 24 V, button yellow, Ø 30 mm
8%
Push button switch fan 12 / 24 V, button yellow, Ø 30 mm
Version: 12/24 V, Yellow button, with lock, Ø 30 mm, 4 blade terminals 6.3 x 0.8...
€47,74 €39,45 €43,92 €36,30
 
SACEX Beacon H1 Saturnello orange 12 V, Ø 128 mm, 204 mm, push-on pin
8%
SACEX
Beacon H1 Saturnello orange 12 V, Ø 128 mm, 204 mm, push-on pin
Nominal voltage: 12 V. Bulbs included: Yes. Light function: Rotating. Diameter: ...
€42,68 €35,27 €39,27 €32,45
 
HELLA Work lamp flood beam H3 55 / 70 W, 153 x 93 x 92 mm, 12 / 24 V
4%
HELLA
Work lamp flood beam H3 55 / 70 W, 153 x 93 x 92 mm, 12 / 24 V
Nominal voltage: 12 / 24 V. Form: Rectangular. Dimensions W x H x D: 153 x 93 x ...
€47,85 €39,55 €46,08 €38,08
 
Work lamp flood beam H3, 55 W, 12 V, 150 x 98 x 89 mm
8%
Work lamp flood beam H3, 55 W, 12 V, 150 x 98 x 89 mm
Bulb: H3. Form: Rectangular. Material: Housing: plastic, lens: glass. Dimensions...
€55,15 €45,58 €50,74 €41,93
 
HELLA Headlight insert left / right H4, 12 / 24 V, built-in
4%
HELLA
Headlight insert left / right H4, 12 / 24 V, built-in
Bulb: H4. To fit: 4551GA 004109021. Installation location: Left/right. Nominal v...
€69,32 €57,29 €66,75 €55,17
 
Pipe RKLE
8%
Pipe RKLE
€102,02 €84,31 €93,86 €77,57
 
Light housing
Light housing
€23,04 €19,04
 
Cover
8%
Cover
€57,95 €47,89 €53,31 €44,06
 
HELLA Work lamp spotlight H3 12 / 24 V, 158 x 162 x 127 mm, bracket assembly
4%
HELLA
Work lamp spotlight H3 12 / 24 V, 158 x 162 x 127 mm, bracket assembly
Nominal voltage: 12 / 24 V. Form: Rectangular. Dimensions W x H x D: 158 x 162 x...
€75,63 €62,50 €72,83 €60,19
 
BOSCH Relays make contact 12 V, 30 A, without bracket, 5-pin, sperdiode
BOSCH
Relays make contact 12 V, 30 A, without bracket, 5-pin, sperdiode
Version: 12 V / 30 A, Without bracket, 5-pin, blade terminal 6.3 mm, With blocki...
€22,96 €18,98
 
Flasher unit electronic 12 V, 6 connections, with holder
8%
Flasher unit electronic 12 V, 6 connections, with holder
Version: Power rating: 12 V / 2 + 1 + 1 / 8 x 21 W, Slim version, with bracket, ...
€50,77 €41,96 €46,71 €38,60
 
Grip hand brake lever Fendt
Grip hand brake lever Fendt
To fit as: Fendt Farmer 303, 304, 307, 308, 309, 310, 311, 312, Favorit 509, 510...
€13,03 €10,76
 
Seal feed pump
Seal feed pump
To fit as: Deutz DX 140, 145, 160
€2,89 €2,39
 
Gasket valve cover Fendt
Gasket valve cover Fendt
To fit as: Fendt FL 120, FL 131, F 231 GT, Farmer 102, F 250 GT
€5,33 €4,40
 
Showing 289 - 336 of 546

Fendt Favorit 612 (Typ 383) specifications

The Fendt Favorit 612 LSA carries the internal type designation T 383 and was built from 1983 to 1993. Within the Favorit 600 series, the 612 occupies a particular position: it was the only model that had been delivered exclusively with four-wheel drive since its introduction in 1968. A rear-wheel drive version only became available in 1974, but the LSA series under Typ 383 was always built exclusively with four-wheel drive. The LS version with rear-wheel drive falls under Typ FWA 283.

There are two production phases. The first (chassis number T 383.210, 1983 to 1987) covers 1,448 units with 135 hp. The second phase (chassis number T 383.211, 1988 to 1993) covers 1,589 units with 145 hp. In 1987, Fendt introduced the Duospeed drive system and the electronically controlled differential lock on the revised 612 LSA. An optional on-board computer was available for processing and storing operational data.

Engine

The Favorit 612 LSA is powered by an MWM TD 226-6.2, a water-cooled six-cylinder four-stroke inline turbodiesel engine with direct injection. The engine is fitted with Rotocap valves, ring carrier pistons, piston crown cooling, a dry air filter with pre-cleaner, an inline injection pump with governor, a multi-hole injector, an oil cooler, a seven-bearing crankshaft, a gear-driven camshaft, a viscous fan, an exhaust turbocharger with pulse charging and thermostatically controlled dual-circuit cooling. Displacement is 6,234 cc in the first phase and 6,240 cc in the second phase.

In the first production phase (1983 to 1987), the engine produces 135 hp. In the second phase (1988 to 1993), output was increased to 145 hp. The torque converter increases torque by up to 30 percent. The lock-up clutch connects engine and gearbox depending on load at 1,600 to 1,900 rpm, reducing or eliminating the need to change gear under load.

Transmission and travel speed

The 612 LSA is fitted with a helical-cut ZF synchronised fine-step gearbox type T 3450 with side-mounted gear selection. The change gearbox has six normal gears and four creep gears. The fine-step section has three positions: slow, fast and reverse. In reverse, sixth gear is locked out. Top speed is 40 km/h in the standard version. There was also an extremely rare 50 km/h version with a modified final drive, achieving approximately 45 km/h in practice. From 1987, the Duospeed gearbox was available, enabling a continuously variable drive range with four power levels.

The main gearbox has four pre-selectable speed ranges: first range 0 to 5.2 km/h, second range 0 to 8.2 km/h, third range 0 to 12.8 km/h and fourth range 0 to 19.4 km/h.

Hydraulics and lift system

The hydraulic tandem pump delivers 72 litres per minute. Maximum lift capacity of the rear three-point hitch is 6,000 kg. The permissible front axle load is 4,000 kg and the rear axle load 6,000 kg.

Power take-off

The PTO is switchable between 540 and 1,000 rpm. An optional front PTO is available.

Brakes, drive and steering

The braking system consists of hydraulically operated full disc brakes on the rear wheels, usable as individual wheel brakes. A propshaft brake acting as a disc brake operates on the four-wheel drive. When the individual wheel brake is applied, the front wheel brake disengages automatically. The parking brake is mechanically operated as an internal shoe brake. The front planetary oscillating axle has an oscillation angle of up to 12 degrees. The rear axle features an electronically controlled differential lock that can be engaged automatically. Steering is hydrostatically assisted.

Dimensions and weight

  • Length: 470 cm
  • Width: 238 cm
  • Height: 289 cm
  • Turning radius: 5.7 m
  • Unladen weight: 6,315 kg
  • Fuel tank: 222 litres

Standard tyre sizes are 16.9-26 at the front and 18.4R38 or 20.8R38 at the rear depending on the version.

Difference from the 612 LS (Typ 283)

A point that regularly comes up is the difference between Typ 383 and Typ 283. The Typ 283 is the LS series with rear-wheel drive and a ZF T 3445 gearbox. The Typ 383 has four-wheel drive as standard, a slightly differently configured ZF T 3450 gearbox, a higher hydraulic pump output and higher permissible axle loads. In addition, the Typ 383 received the Duospeed drive system and the electronically controlled differential lock in its second phase, which the Typ 283 does not have.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart