Menu
EUR

Fiat 566 tractor parts & technical data

What fits a Fiat 566? You can see it at a glance here: more than 120 parts, including lighting and brake and transmission parts for this tractor.

124 parts found for Fiat 566
Show:
Crankshaft seal rear Ø 110 x 135 x 13 mm Fiat
Outer Ø: 135 mm. Width: 13 mm. Inner Ø: 110 mm. More
Outer Ø: 135 mm. Width: 13 mm. Inner Ø: 110 mm.
€24,14 €19,95
Silencer vertical 680 mm, inner Ø 45 mm Ford, Fiat
Version: Length: 680 mm, Inner Ø: 45 mm. More
Version: Length: 680 mm, Inner Ø: 45 mm.
€81,28 €67,17 €74,78 €61,80
You save 8%
Bosch/Rexroth Hydraulic pump 11 cm³/rpm., taper 1:8, Ø 17,46 mm, clockwise
Bosch/Rexroth
Output volume: 11 cc/rev. Drive shaft: Taper 1:8, Ø 17.46. Direction of rotation: Right. Bosch no.: 0510525046. More
Output volume: 11 cc/rev. Drive shaft: Taper 1:8, Ø 17.46. Direction ...
€459,16 €379,47 €422,43 €349,11
You save 8%
Spacer 25 x 42 x 24 mm Case IH, Fiat, New Holland
Dimensions: 25 x 42 x 24 mm. More
Dimensions: 25 x 42 x 24 mm.
€27,15 €22,44
Cobo Replacement key plastic-coated black
Cobo
Version: To fit: Case IH, Fiat, Volvo + Cobo: 22714132000, 22714159000. More
Version: To fit: Case IH, Fiat, Volvo + Cobo: 22714132000, 22714159000...
€13,89 €11,48
Cobo Lamp glass right
Cobo
Installation location: Right. More
Installation location: Right.
€19,43 €16,05
Cobo Lamp glass left
Cobo
Installation location: Left. Menke no.: 55039. More
Installation location: Left. Menke no.: 55039.
€29,03 €23,99
Tube exhaust curved vertical enamelled 700 mm, Ø 49 mm Fiat
To fit as: Fiat 446, 466, 566, 666, 766, 570, 670, 580, 680, 780, 55-46, 60-46, 65-46, 55-56, 60-56, 65-56, 70-56, 55-60, 45-66, 50-66, 55-66, 60-66, ... More
To fit as: Fiat 446, 466, 566, 666, 766, 570, 670, 580, 680, 780, 55-4...
€49,96 €41,29 €45,96 €37,99
You save 8%
Thermostat Ø 54 mm, 79 °C Ford, Case IH, Fiat, Steyr, New Holland
To fit as: New Holland TD 55D, 65D, 75D, 85D, 95D, TL 70, 80, 90, 100, TN 55, 65, 70, 75, 80, 90, 95, L 60, 65, 75, 85, 95 More
To fit as: New Holland TD 55D, 65D, 75D, 85D, 95D, TL 70, 80, 90, 100,...
€24,35 €20,12
Thrust washer Ø 171,1 x 94,3 mm, thickness 2,65 mm
Thickness: 2,65 mm. Outer Ø: 171,1 mm. Inner Ø: 94,3 mm. More
Thickness: 2,65 mm. Outer Ø: 171,1 mm. Inner Ø: 94,3 mm.
€23,60 €19,50
Water pump with gasket Fiat engine 8035.01-8065.02
To fit: Fiat. Version: With gasket. More
To fit: Fiat. Version: With gasket.
€127,68 €105,52 €117,47 €97,08
You save 8%
Tank cap tank collar Ø 64 mm
Filler neck Ø: 64 mm. More
Filler neck Ø: 64 mm.
€21,23 €17,54
Bosch/Rexroth Hydraulic pump 14 cm³/rpm., taper 1:8, Ø 17,46, 7/16-20 UNF, left Fiat
Bosch/Rexroth
Drive shaft: Taper 1:8, Ø 17.46- 7/16-20 UNF. Direction of rotation: Anticlockwise. Output volume: 14 cc/rev. Line connection suction side: Ø 40mm, ... More
Drive shaft: Taper 1:8, Ø 17.46- 7/16-20 UNF. Direction of rotation: ...
€511,82 €422,99 €470,87 €389,15
You save 8%
Bush left lift arm shaft 62,8 x 68,2 x 40 mm Ford, Fiat, New Holland
Dimensions: 62.8 x 68.2 x 40 mm. More
Dimensions: 62.8 x 68.2 x 40 mm.
€23,03 €19,03
Cobo Tank sender length 313 mm
Cobo
Version: Length: 313 mm. More
Version: Length: 313 mm.
€81,84 €67,64 €75,29 €62,23
You save 8%
Angle drive tractormeter side 2 x M16 x 1
Version: Thread: 2 x M16 x 1. More
Version: Thread: 2 x M16 x 1.
€64,09 €52,97 €58,96 €48,73
You save 8%
Tank cap tank collar Ø 64 mm Fiat 415-1000
To fit as: Fiat 315, 415, 850, 1000, 446, 466, 511, 512, 566, 612, 615, 666, 715, 766, 55-46, 60-46, 65-46, 55-56, 60-56, 65-56, 70-56, 55-66, 60-66, ... More
To fit as: Fiat 315, 415, 850, 1000, 446, 466, 511, 512, 566, 612, 615...
€21,23 €17,54
Spacer 25 x 40 x 25 mm Fiat series 66 - 94, L 60 - L 95
Dimensions: 25 x 40 x 25 mm. More
Dimensions: 25 x 40 x 25 mm.
€10,51 €8,69
Ring 23 x 40 x 25 mm Fiat L 60-95, New Holland TN55-TN95
Dimensions: 23 x 40 x 25 mm. More
Dimensions: 23 x 40 x 25 mm.
€10,40 €8,60
Drive shaft 1090 mm, M16 x 1,5 / M18 x 1,5
Thread: M16 x 1.5 / M18 x 1.5. Length: 1090 mm. More
Thread: M16 x 1.5 / M18 x 1.5. Length: 1090 mm.
€25,54 €21,11
Showing 97 - 124 of 124

Fiat 566 parts for the clutch, cooling and lights

Most Fiat 566 owners come to this page with one of three jobs in mind: a clutch that slips, an engine that runs too hot or too cold, or a light that no longer works. All three are covered by the more than 120 replacement parts that fit the 566, supplied by GRANIT and by brands such as LUK, SACHS, FEBI and Cobo.

Clutch

For the driving clutch there are complete clutch kits, double clutches, clutch plates and thrust bearings. A kit contains the parts that wear together and finishes the job in one go. If you replace parts separately, always include the thrust bearing. Centre the clutch plate with an alignment tool before bolting up the pressure plate, then tighten its bolts in a cross pattern over several passes so it pulls down evenly and the clutch does not judder.

Cooling and engine

For the cooling system there are thermostats, water pump gaskets and V-belts. The engine is covered by crankshaft seals, spacers, bolt sets and engine oil filters for routine servicing, and the charging side by alternators. When a thermostat is replaced, fit a new gasket at the same time rather than reusing the old one.

Exhaust and lights

For the exhaust there are pipes, including a curved vertical pipe with an enamelled finish. For the lighting you will find headlights and separate lamp glasses, so a cracked glass does not mean a whole new lamp.

Oil changes and the V-belt

Every oil change calls for a new engine oil filter. Smear the rubber ring of the new filter with a little clean oil and screw it on by hand, without a filter wrench. Run the engine briefly afterwards and check for leaks.

If the alternator is not charging or you hear a squeal when you open the throttle, look at the V-belt. A belt with glazed flanks, cracks or too much slack will slip and no longer drive the alternator and water pump properly. Retension a new belt after the first few hours of work, as it stretches slightly at first.

Making sure it fits

Check the type plate, then look at the part you are replacing. Clutch plates, thrust bearings and gaskets often carry a reference number you can compare with the new part, and with a clutch plate the diameter and spline count matter too.

Within the Fiat range, the 566 sits in the 66 series alongside several close relatives. The Fiat 60-66, Fiat 65-66 and Fiat 70-66 each have their own page showing what fits those tractors. For other Fiat models, start at Fiat parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison
This product has been added to your cart