Menu
EUR

Fiat 85-90 tractor parts & technical data

Looking after a Fiat 85-90 from the 90 series? Choose from more than 250 matching parts, with lighting, trailer couplings and electrics well represented.

253 parts found for Fiat 85-90
Show:
Eaton As transmission Case IH, Fiat, Ford, New Holland, 3,10 kg
Eaton
As transmission Case IH, Fiat, Ford, New Holland, 3,10 kg
Reference no.: 47132984
€201,80 €166,78
 
Eaton Link wheel Case IH, Fiat, Ford, New Holland
5%
Eaton
Link wheel Case IH, Fiat, Ford, New Holland
Reference no.: 5125007
€287,74 €237,80 €273,35 €225,91
 
GRANIT Thrust washer drive shaft Fiat series 80-94
GRANIT
Thrust washer drive shaft Fiat series 80-94
€36,35 €30,04
 
Track rod complete 1520 mm, M20 x 1, 18 - 20 mm, 34 mm
5%
Track rod complete 1520 mm, M20 x 1, 18 - 20 mm, 34 mm
A: 1500 mm. B: M20 x 1 mm. C: 18 - 20 mm. G: . D: M16 x 1,5 mm. E: 34 mm. F: 22,...
€237,29 €196,11 €225,40 €186,28
 
LUK Pilot bearing 17 x 47 x 14 mm
5%
LUK
Pilot bearing 17 x 47 x 14 mm
Dimensions: 17 x 47 x 14 mm. Menke no.: 167836.
€32,31 €26,70 €30,65 €25,33
 
V-belt Fiat, Renault
V-belt Fiat, Renault
€19,00 €15,70
 
Tank cap Fiat series 46-93
Tank cap Fiat series 46-93
€7,55 €6,24
 
GRANIT O-ring 25,07 x 2,62 mm Fiat
GRANIT
O-ring 25,07 x 2,62 mm Fiat
Dimensions: 25.07 x 2.62 mm.
€1,00 €0,83
 
GRANIT Nut cylinder head Ford, Fiat, New Holland
GRANIT
Nut cylinder head Ford, Fiat, New Holland
€17,70 €14,63
 
GRANIT Crankshaft seal Ø 42 x 65 x 12 mm Case IH, Fiat, Steyr, New Holland
GRANIT
Crankshaft seal Ø 42 x 65 x 12 mm Case IH, Fiat, Steyr, New Holland
Outer Ø: 65 mm. Width: 12 mm. Inner Ø: 42 mm.
€5,00 €4,13
 
GRANIT Fuel tank Fiat series 88, 90, 93, 94
5%
GRANIT
Fuel tank Fiat series 88, 90, 93, 94
€642,51 €531,00 €610,35 €504,42
 
Seal water pump Fiat, Ford
Seal water pump Fiat, Ford
€3,81 €3,15
 
Bosch/Rexroth Hydraulic pump 19 cm³/rpm., taper 1:8, Ø 17,46 mm, anticlockwise
5%
Bosch/Rexroth
Hydraulic pump 19 cm³/rpm., taper 1:8, Ø 17,46 mm, anticlockwise
Output volume: 19 cc/rev. Drive shaft: Taper 1:8, Ø 17.46. Direction of rotation...
€446,89 €369,33 €424,50 €350,83
 
Bosch/Rexroth Hydraulic pump clockwise rotating with valve 14 cm³/rpm., taper 1:8 Ø 17,46
5%
Bosch/Rexroth
Hydraulic pump clockwise rotating with valve 14 cm³/rpm., taper 1:8 Ø 17,46
Drive shaft: Taper 1:8, Ø 17.46. Direction of rotation: Right. Output volume: 14...
€891,16 €736,50 €846,60 €699,67
 
Spacer 25 x 40 x 25 mm Fiat series 66 - 94, L 60 - L 95
Spacer 25 x 40 x 25 mm Fiat series 66 - 94, L 60 - L 95
Dimensions: 25 x 40 x 25 mm.
€10,00 €8,26
 
GRANIT Ring 23 x 40 x 25 mm Fiat L 60-95, New Holland TN55-TN95
GRANIT
Ring 23 x 40 x 25 mm Fiat L 60-95, New Holland TN55-TN95
Dimensions: 23 x 40 x 25 mm.
€9,95 €8,22
 
GRANIT Spacer 25 x 42 x 24 mm Case IH, Fiat, New Holland
GRANIT
Spacer 25 x 42 x 24 mm Case IH, Fiat, New Holland
Dimensions: 25 x 42 x 24 mm.
€26,00 €21,49
 
GRANIT Sealing ring lift arm shaft 23 x 37 x 11 mm Ford, Case IH, Fiat, New Holland
GRANIT
Sealing ring lift arm shaft 23 x 37 x 11 mm Ford, Case IH, Fiat, New Holland
Dimensions: 23 x 37 x 11 mm.
€24,15 €19,96
 
GRANIT Lateral strut right and left 318 mm, Ø 30 mm, ball Ø 19 mm Fiat
5%
GRANIT
Lateral strut right and left 318 mm, Ø 30 mm, ball Ø 19 mm Fiat
Ø A: 30 mm. Dimensions: Ball Ø = 19 mm. Length: 318 mm.
€47,32 €39,11 €44,95 €37,15
 
Spindle thread M27 x 3 Fiat
Spindle thread M27 x 3 Fiat
Dimensions: Thread = M27 x 3 mm.
€30,45 €25,17
 
Showing 97 - 120 of 253

Fiat 85-90 parts

Plenty of Fiat 85-90 tractors are still doing a full day's work, and keeping them that way comes down to good wear parts. This page holds more than 250 parts that fit the Fiat 85-90, from GRANIT and from makers such as Cobo, LUK, MAHLE and Eaton.

Steering and linkage

For the steering there are ball joints. To check one, have someone rock the steering wheel back and forth while you hold the joint. A knock or movement inside the joint itself means it is due. A torn dust boot lets water in and the joint will not last long after that.

For the three point linkage you will find lift rods and seals for the lift cylinder. If the linkage slowly drops with the engine stopped, oil is often getting past the piston seal of the lift cylinder.

Clutch and driveline

Clutch kits, double clutch pressure plates and thrust bearings belong together. When the clutch is renewed, fit a new thrust bearing as well, because it sits deep inside and nobody wants to split the tractor twice. Gear wheels for the driveline are available too. Check the flywheel face for scoring while the tractor is split.

Engine, electrics and filters

Engine parts include turbocharger and exhaust manifold gaskets, piston sealing rings and O-rings, for instance for the brake cylinder. Alternators and gear reduction starters cover the electrics, and drawbars and lamp glass round things off. A gear reduction starter is worth considering if the old starter struggles to turn the engine on cold days.

Among the air filters you will find secondary elements. The inner element is a safety filter. Do not blow it out with compressed air. Replace it instead, for example at every second or third change of the main filter.

Working out which part you need

The model and chassis number of your 85-90 are on the rating plate. For a clutch, lay the old plate and pressure plate side by side and compare the diameter and the number of springs. Seals and bearings usually carry a size or a number you can look up.

The 85-90 is part of the Fiat 90 series, and several other models from it have their own page: Fiat 55-90, Fiat 60-90, Fiat 80-90, Fiat 90-90, Fiat 100-90 and Fiat 110-90. If one of those works next to your 85-90, check its own page for what fits. All other Fiat tractors are under Fiat parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart