Menu
EUR

Fendt Favorit 611 (Typ 382) parts

Looking for parts for your Fendt Favorit 611 (Typ 382) tractor? In this category, you'll find everything you need for the maintenance and repair of your vehicle.

568 parts found for Fendt Favorit 611 (Typ 382)
Show:
Set of parts filter glass Ø 29/35 x 53 mm
Ø: 29/35 mm. Height: 33 mm. More
Ø: 29/35 mm. Height: 33 mm.
€13,54 €11,19
Stabilus Windshield frame shock absorber 250 N, 600,5 mm, stroke 252,5 mm Fendt
Stabilus
To fit as: Fendt Windscreen More
To fit as: Fendt Windscreen
€42,70 €35,29 €39,28 €32,47
You save 8%
Outlet valve engine D 327 Fendt F 231 GT
To fit as: Fendt F 231 GT from serial no. 16774 More
To fit as: Fendt F 231 GT from serial no. 16774
€29,20 €24,13
Repair set clutch cylinder DOT4 Fendt
Medium: DOT4. Additional information: With piston. More
Medium: DOT4. Additional information: With piston.
€83,50 €69,01 €76,82 €63,49
You save 8%
Wabco Connector head red supply line M16 x 1,5, vehicle
Wabco
Version: Red, supply line. Connection: M16 x 1.5. Operating pressure max.: 10.0 bar. Vehicle/application: Red, supply, towing vehicle. More
Version: Red, supply line. Connection: M16 x 1.5. Operating pressure m...
€30,40 €25,12
Wabco Cover antifreeze pump Fendt, Massey Ferguson, Case IH
€60,86 €50,30 €55,99 €46,27
You save 8%
Wabco Compressor 10 bar, 159 cm³, Ø 75 mm, stroke 36 mm, M18 x 1,5 Fendt
Wabco
Operating pressure max.: 10 bar. Cylinder capacity: 159 cm³. Speed: 3000 1/min.. Piston Ø: 75 mm. Piston stroke: 36 mm. Cooling system: Air. Thread:... More
Operating pressure max.: 10 bar. Cylinder capacity: 159 cm³. Speed: 3...
€2.699,82 €2.231,26 €2.587,27 €2.138,24
You save 4%
Wabco Compressor 10 bar, 106 cm³, Ø 75 mm, stroke 24 mm, crankshaft 25 mm Fendt
Wabco
Operating pressure max.: 10 bar. Cylinder capacity: 106 cm³. Speed: 3000 1/min.. Piston Ø: 75 mm. Piston stroke: 24 mm. Cooling system: Air. Thread:... More
Operating pressure max.: 10 bar. Cylinder capacity: 106 cm³. Speed: 3...
€2.631,33 €2.174,65 €2.521,64 €2.084,00
You save 4%
LUK Pilot bearing 40 x 68 x 15 mm
LUK
Dimensions: 40 x 68 x 15 mm. More
Dimensions: 40 x 68 x 15 mm.
€70,71 €58,44 €65,05 €53,76
You save 8%
Wheel brake cylinder Ø 38,1 mm, DOT 4 Fendt Favorit 600-615
€329,17 €272,04 €302,84 €250,28
You save 8%
Gear change gate Fendt
Sealing ring 58 x 80 x 10/12 mm Fendt Favorit 611-615
Version: 58 x 80 x 10 / 12 mm. More
Version: 58 x 80 x 10 / 12 mm.
€67,44 €55,74 €62,04 €51,28
You save 8%
Gaiter gear lever Fendt
Compression spring shifting 19,5 mm, Ø 10,5 mm, wire thickness 1,5 mm Fendt
Dimensions: Length 19,5, Ø 10,5, Wire thickness 1,5. More
Dimensions: Length 19,5, Ø 10,5, Wire thickness 1,5.
€5,24 €4,33
Bush rear axle outer Fendt Favorit 610, 611
€463,53 €383,08 €426,45 €352,44
You save 8%
Starter ring gear Ø 350/316 mm, 115 teeth Fendt
Version: Ø 350/316 mm, 115 splines. More
Version: Ø 350/316 mm, 115 splines.
€514,17 €424,93 €473,04 €390,94
You save 8%
Clutch carrier Ø 375 mm Fendt
€332,65 €274,92 €306,04 €252,92
You save 8%
Clutch carrier Ø 400 mm Fendt Favorit 611-615
€1.077,42 €890,43 €991,23 €819,20
You save 8%
Disc
To fit as Fendt. More
To fit as Fendt.
€4,01 €3,32
Replacement glass, main mirror curved 366 x 176 x 3 mm, unheated
Dimensions (mm): 366 x 176 x 3. Version: Unheated. Installation location: Right/left. Radius of curvature (mm): 1800. More
Dimensions (mm): 366 x 176 x 3. Version: Unheated. Installation locati...
€30,89 €25,53
Breather filter
€35,83 €29,61 €32,96 €27,24
You save 8%
BOSCH Injection nozzle Fendt Farmer 304-310, Favorit 611-615
€113,33 €93,66 €96,05 €79,38
You save 15%
KS Connecting rod bearing Ø 63 mm, width 27 mm
€64,09 €52,97 €58,96 €48,73
You save 8%
VICTOR REINZ Crankshaft seal for Fendt, Deutz-Fahr
€67,80 €56,03 €62,38 €51,55
You save 8%
VICTOR REINZ Valve stem seal set Ø 9 x 1,5 mm
€39,01 €32,24
Cooling fan Ø 515 mm Fendt Favorit 611-615
€383,84 €317,22 €353,13 €291,85
You save 8%
Hose thermostat - heating valve Ø 18 mm, length 1700 mm Fendt
Inner Ø: 18 mm. Length: 1700 mm. Material thickness: 3,5 mm. More
Inner Ø: 18 mm. Length: 1700 mm. Material thickness: 3,5 mm.
€47,02 €38,86 €43,26 €35,75
You save 8%
Fan clutch Fendt Favorit 611-615
€318,50 €263,22 €293,02 €242,17
You save 8%
Radiator hose, bottom Ø 44 mm, length 100 mm Fendt
Inner Ø: 44 mm. Length: 100 mm. More
Inner Ø: 44 mm. Length: 100 mm.
€33,84 €27,96
Radiator hose radiator / thermostat inner-Ø 45 mm Fendt
€85,28 €70,48 €78,46 €64,84
You save 8%
Radiator hose thermostat / pressure pipe cylinder head Ø 45 mm Fendt
Thermostat Ø 45/45/25 mm, 75 °C Fendt
Ø: 45/45/25 mm. Temperature: 75 °C. More
Ø: 45/45/25 mm. Temperature: 75 °C.
€291,73 €241,10 €268,39 €221,81
You save 8%
Water pump with gasket Fendt
To fit: Fendt Farmer, Favorit. More
To fit: Fendt Farmer, Favorit.
€161,28 €133,29 €148,38 €122,63
You save 8%
Outlet valve Fendt
€60,40 €49,92 €55,57 €45,92
You save 8%
Main bearing standard Ø 70 mm Fendt, Renault
Dimensions: Ø 70 mm. More
Dimensions: Ø 70 mm.
€35,72 €29,52 €32,86 €27,16
You save 8%
Connecting rod bush Ø 35 mm Fendt
Dimensions: 35 mm. More
Dimensions: 35 mm.
€26,81 €22,16
Crankshaft seal for Ø 78 x 100 x 13 mm Fendt
Outer Ø: 100 mm. Width: 13 mm. Inner Ø: 78 mm. Menke no.: 59595. More
Outer Ø: 100 mm. Width: 13 mm. Inner Ø: 78 mm. Menke no.: 59595.
€31,29 €25,86
Cylinder head bolt 14 x 158 mm Case IH, Steyr, Fendt
Dimensions: M14 x 158 mm. More
Dimensions: M14 x 158 mm.
€35,29 €29,17 €32,47 €26,83
You save 8%
Cover crankshaft rear Fendt
€652,71 €539,43 €600,49 €496,28
You save 8%
Bleed valve Fendt Farmer 102-312, Favorit 509-615, GT 231
€57,92 €47,87 €53,29 €44,04
You save 8%
Oil drain valve thread 1/2 inch - 20UNF Fendt, Massey Ferguson
€68,16 €56,33 €62,71 €51,82
You save 8%
Showing 433 - 480 of 568

Fendt Favorit 611 (Typ 382) specifications

The Fendt Favorit 611 LSA carries the internal type designation T 382 and was built from 1985 to 1993 exclusively with four-wheel drive. A total of 1,433 units were produced. The 611 LSA is the successor to the 611 LS (Typ 282) and at the same time the conclusion of a development line that began in 1972 with the Favorit 611 S. The LS version with rear-wheel drive falls under Typ FWA 282.

Production ran in two clearly distinct phases. In the first phase (chassis number T 382.250, 1985 to 1987, 228 units), the engine has no turbocharger and produces 115 hp. In the second phase (chassis number T 382.211, 1988 to 1993, 1,205 units), a turbocharger was added and the combustion process optimised, raising output to 125 hp while fuel consumption fell. The 611 LSA was succeeded in the line-up by the Favorit 500C series.

Hydraulics and lift system

The hydraulic tandem pump delivers 69 litres per minute (44 plus 25 litres) at 180 bar. The rear three-point hitch achieves a maximum lift capacity of 7,410 kg. An optional front linkage with category II three-point hitch is available with a maximum lift capacity of 3,940 kg. The permissible front axle load is 3,050 kg and the rear axle load 5,400 kg. The permissible gross weight is 8,500 kg.

Engine

The second phase (1988 to 1993) uses an MWM TD 226-B 6, a water-cooled six-cylinder four-stroke inline turbodiesel engine with direct injection into the combustion bowl of the piston. The engine is fitted with individually mounted cylinder heads, piston crown cooling, an oil cooler, Rotocap valves, a viscous fan, an inline injection pump, a multi-hole injector, a dry air filter with pre-cleaner, pressure circulation lubrication, an exhaust turbocharger with pulse charging and thermostatically controlled dual-circuit cooling. Displacement is 6,240 cc. Maximum torque is 497 Nm at 1,500 rpm. Injection pressure is 180 to 185 bar, raised to 650 bar from 1987.

The first phase (1985 to 1987) has a naturally aspirated MWM D 226.6.2 without turbocharger producing 115 hp, with a maximum torque of 412 Nm at 1,500 rpm.

Transmission and travel speed

The 611 LSA has a helical-cut ZF fully synchronised fine-step gearbox type T 3345 with side-mounted gear selection, offering 20 forward and 9 reverse gears. Top speed is 40 km/h in the standard version, with a 30 km/h version also available. In the 40 km/h version, the six gears in the fast range run from 3.88 to 38.41 km/h, in the slow range from 3.12 to 30.94 km/h and in the creep range from 4.71 to 27.41 km/h. From 1987, the Duospeed drive system was available as an option, along with an electronically controlled differential lock and a reversing unit.

Power take-off

The PTO is switchable between 540 and 1,000 rpm. An optional front PTO is available.

Brakes and steering

The braking system consists of hydraulically operated full disc brakes on the rear wheels, usable as individual wheel brakes. A propshaft disc brake acts on the four-wheel drive; when the individual wheel brake is applied, the front wheel brake disengages automatically. The parking brake is mechanically operated as an internal shoe brake. Steering is hydrostatically assisted.

Dimensions and weight

  • Unladen weight: 6,080 kg
  • Fuel tank: 222 litres
  • Fuel consumption at maximum power: 223 g/kWh

Standard tyre sizes are 14.9-26 at the front and 18.4R38 at the rear. The cab is a rubber-mounted, vibration and sound-insulated safety cab with a noise level of 78 dB, air-suspended seat, digital tractor meter, fold-open front and rear windows, roof hatch, three-stage ventilation system, two-stage heating, radio preparation and height-adjustable steering wheel.

Difference from the 611 LS (Typ 282)

The difference between Typ 382 and Typ 282 is a recurring point when sourcing parts and when purchasing. The Typ 282 is the LS series, built from 1977 to 1984, available with either rear-wheel or four-wheel drive and producing 100 to 110 hp from a naturally aspirated engine. The Typ 382 is available exclusively with four-wheel drive, has a turbocharged engine in its second phase, a higher hydraulic pump output and higher permissible axle loads. The gearbox on both types is a ZF T 3345, but the configuration differs between phases.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart