Menu
EUR

Fiat 90-90 tractor parts & technical data

If there is a Fiat 90-90 in your yard, this is your overview: more than 200 parts for the 90 series, including lighting, electrics and trailer couplings.

235 parts found for Fiat 90-90
Show:
Scharmüller Drawbar pin-Ø 38 mm, 1279 mm, category 3, black Fiat
Scharmüller
Colour: Black | Mounting position: 2 | D-value (kN): 93,7 | Width (mm): 90 | Lock: Pin | Length (mm): 1279 | Category: Drawbar | Version: Standard | H... More
Colour: Black | Mounting position: 2 | D-value (kN): 93,7 | Width (mm)...
€736,45 €608,64
LUK Thrust bearing 50 x 90 x 21,6 mm
LUK
Dimensions (mm): 50 x 90 x 21.6 More
Dimensions (mm): 50 x 90 x 21.6
€85,00 €70,25 €80,75 €66,74
You save 5%
Clutch kit Fiat 880, 980, 90-90 - 110-90
Contents: Clutch (445K88876102), organic disc (445S64914003), release bearing (44517000), release bearing (445A63839000) More
Contents: Clutch (445K88876102), organic disc (445S64914003), release ...
€756,55 €625,25 €718,70 €593,97
You save 5%
HELLA Alternator 14 V, 65 A, without belt pulley
HELLA
Nominal voltage (V): 14 | Additional information: Without pulley | Nominal values (V / A): 14 / 65 | Charging current (A): 65 More
Nominal voltage (V): 14 | Additional information: Without pulley | Nom...
€304,81 €251,91 €245,00 €202,48
You save 20%
FEBI Fuel filter WK842
€19,60 €16,20 €8,47 €7,00
You save 57%
Bush drive shaft 12 teeth Fiat Series 90, M 100-160, F 100-140
€36,42 €30,10 €34,55 €28,55
You save 5%
Ball joint 106 mm, taper 20 - 22 mm, M18 x 1,5, M24 x 1,5
A: 106 mm. C: M18 x 1,5 mm. D: M24 x 1,5 mm. E: 20 mm. F: 22 mm. Taper: 20 - 22 mm. More
A: 106 mm. C: M18 x 1,5 mm. D: M24 x 1,5 mm. E: 20 mm. F: 22 mm. Taper...
€57,56 €47,57 €54,65 €45,17
You save 5%
Lever with bolt and lock steering valve Fiat, Ford, New Holland
€85,28 €70,48 €81,00 €66,94
You save 5%
GRANIT Joint Fiat 90-90, 100-90, 110-90
€75,63 €62,50 €71,80 €59,34
You save 5%
Signal transmitter temperature thread M16
Version: Temperature, thread: M16. More
Version: Temperature, thread: M16.
€22,80 €18,84
Cobo Multifunction switch horn, lighting, indicators
Cobo
Version: For horn, lights, indicators. More
Version: For horn, lights, indicators.
€135,54 €112,02 €128,75 €106,41
You save 5%
Cobo Fuse box 12-pin blade fuse connection, 174 x 50 x 34,5 mm
Cobo
Version: Without fuses, blade terminal connection at the bottom, transparent cover, L 174 x W 50 x H 34.5 mm. To fit: Blade terminal. Number of pins: ... More
Version: Without fuses, blade terminal connection at the bottom, trans...
€90,71 €74,97 €82,00 €67,77
You save 10%
Flasher unit 12 V, 2+1+1 x 21 W, with holder and indicator instruments
To fit as: Case IH 238, 248, 258, 268, 278, 288, 323, 354, 374, 384, 444, 474, 475, 484, 584, 674, 684, 784, 884 385, 485, 485XL, 585, 585XL, 685, 685... More
To fit as: Case IH 238, 248, 258, 268, 278, 288, 323, 354, 374, 384, 4...
€48,98 €40,48 €44,30 €36,61
You save 10%
GRANIT External plate 1,5 mm, inner 100 mm, outer 152 mm, 6 teeth
GRANIT
Version: Thickness: 1.5 mm Inner: 100 mm Outer: 152 mm 6 teeth More
Version: Thickness: 1.5 mm Inner: 100 mm Outer: 152 mm 6 teeth
€10,65 €8,80
SACHS Thrust bearing 50 x 80 mm, 89 x 22 mm
SACHS
Dimensions (mm): 50 x 80 89 x 22 More
Dimensions (mm): 50 x 80 89 x 22
€84,70 €70,00 €72,85 €60,21
You save 14%
LUK Thrust bearing PTO clutch 75 x 115 x 20 mm
LUK
Dimensions (mm): 75 x 115 x 20 More
Dimensions (mm): 75 x 115 x 20
€175,89 €145,36 €167,00 €138,02
You save 5%
Showing 145 - 168 of 235

Fiat 90-90 parts for the linkage, engine and steering

Most Fiat 90-90 tractors have a lot of hours behind them, and it shows in seals, bearings and bushes. More than 200 replacement parts fit this model, from GRANIT and from makers such as Cobo, Walterscheid, Bosch/Rexroth and FLEETGUARD.

Bringing the linkage back to life

If the linkage slowly drops with an implement on, the leak is often in the lift cylinder. There are seals for the outer lift cylinder and piston sealing rings, along with bushes for the lift arm shaft and lift rods. For oil pressure there is a single hydraulic pump from Bosch/Rexroth. Before fitting new seals, inspect the cylinder bore for scoring. A groove in the bore will chew through fresh seals in no time and the job will have been wasted.

Engine, clutch and front axle

For cooling there is a thermostat with its O-ring, plus gaskets for the water pump and the rear engine cover. A FLEETGUARD air filter with a separate inner element keeps the intake clean. The driving clutch can take a new thrust bearing, the steering new ball joints, and the brakes new brake cylinder O-rings. Lamp glasses, holders, yokes and rocker switches complete the list.

A quick note on the inner air filter: replace it rather than blowing it out. It is the last line of defence for the engine if the outer element is ever damaged.

Thrust bearing and clutch

A thrust bearing that sings or rattles as soon as you press the clutch pedal needs replacing. The tractor has to be split to reach it, so inspect the clutch plate and pressure plate on the same job. Reset the pedal play after fitting. With too little play the bearing turns all the time and the new one will soon be worn out too.

Ordering the right part

On an older tractor the type plate can be weathered, so clean it carefully to confirm you have a 90-90. For seals, bushes and bearings, measure the old part and compare the bore, outside size and width with the product details. Filters usually have a clearly printed reference number on the housing.

The rest of the 90 series

The 90 series came in several sizes, and each one has a page here with the parts that fit it:

For the rest of the brand, go to Fiat parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart