Menu
EUR

Massey Ferguson 3640 tractor parts & technical data

Three-point linkage parts, trailer couplings and electrics for the Massey Ferguson 3640 are collected here: more than 90 parts for this 3600 series tractor.

89 parts found for Massey Ferguson 3640
Show:
Crankshaft seal for Ø 58 x 80 x 12 mm Massey Ferguson
Outer Ø: 80 mm. Width: 12 mm. Inner Ø: 58 mm. More
Outer Ø: 80 mm. Width: 12 mm. Inner Ø: 58 mm.
€15,49 €12,80
Feed pump 4 hole, 25 x 44 mm, flange up to end lever 56 mm
Version: 4 holes, Vertical hole spacing: 25 mm, Horizontal hole spacing: 44 mm, Flange to lever end: 56 mm. More
Version: 4 holes, Vertical hole spacing: 25 mm, Horizontal hole spacin...
€42,63 €35,23 €39,22 €32,41
You save 8%
Oil sump gasket engine 1006.6 Massey Ferguson 3085-8220
€69,27 €57,25 €63,73 €52,67
You save 8%
Connecting rod bearing standard, Ø 63,47 mm Landini, Massey Ferguson
€21,81 €18,03
Cylinder head gasket engine Sisu
€82,88 €68,50 €76,25 €63,02
You save 8%
Hydraulic top link cat. 2/2, 500 - 689 mm, stroke 189 mm, Ø 63 mm
A cat.: 2 / 25,4. B cat.: 2 / 25,4. F: 500 / 689 mm. Piston rod Ø D: 35 mm. Cylinder Ø inner E: 63 mm. Check valve: at side. Lifting force: 5 t. Ten... More
A cat.: 2 / 25,4. B cat.: 2 / 25,4. F: 500 / 689 mm. Piston rod Ø D: ...
€577,92 €477,62 €531,69 €439,41
You save 8%
Hydraulic top link cat. 2, 500 - 726 mm, stroke 226 mm, Ø 63 mm
Top link type: hydraulic. Type: Ball joint/ball joint. A cat.: 2 / 25,4. B cat.: 2 / 25,4. F: 500 / 726 mm. Stroke: 226 mm. Piston rod Ø D: 35 mm. Cy... More
Top link type: hydraulic. Type: Ball joint/ball joint. A cat.: 2 / 25,...
€466,96 €385,92 €429,60 €355,04
You save 8%
Scharmüller Forced steering support plates left Ball 80 to K50 250 mm, 2 ton
Scharmüller
Assembly notes: Anticlockwise. Connection position: 250 mm. Lock: K50. Colour: Black. Steering power: 2 t. Description: Approved for steering forces u... More
Assembly notes: Anticlockwise. Connection position: 250 mm. Lock: K50....
€576,39 €476,36 €564,40 €466,45
You save 2%
Walterscheid Drawbar ball 50 rail 199 mm, pin Ø 22 mm, 150 kg, black
Walterscheid
Rail width: 199 mm. Guide width: 30 mm. Detent pin Ø: 22 mm. Load capacity: 150 kg. D-value: 23,5 kN. Plate height: 120 mm. Colour: Black. Descriptio... More
Rail width: 199 mm. Guide width: 30 mm. Detent pin Ø: 22 mm. Load cap...
€1.085,41 €897,03 €975,15 €805,91
You save 10%
Belt tensioner Ø 75 mm, width 46,5 mm, Massey Ferguson and Fendt
Outer Ø: 75 mm. Width: 46,5 mm. More
Outer Ø: 75 mm. Width: 46,5 mm.
€117,22 €96,88
Oil cooler Massey Ferguson series 3000-7200
€357,89 €295,78 €329,26 €272,11
You save 8%
Radiator Massey Ferguson 3640, 5425-5455, 6445, 6455
To fit as: Massey Ferguson Serie 3000, 3640, Serie 5400 (5425, 5435, 5445, 5455 Tier 3), Serie 6400 (6445, 6455 Tier 3). More
To fit as: Massey Ferguson Serie 3000, 3640, Serie 5400 (5425, 5435, 5...
€856,21 €707,61 €837,71 €692,32
You save 2%
Inlet valve engine Sisu 320-620
€38,19 €31,56 €35,13 €29,04
You save 8%
Piston ring set 3 rings Ø 108 mm, 3 mm trapezoidal ring / 3 mm / 4 mm
Dimensions: 3 rings, Ø 108 mm, 3 mm (trapezoidal ring) / 3 mm / 4 mm. More
Dimensions: 3 rings, Ø 108 mm, 3 mm (trapezoidal ring) / 3 mm / 4 mm.
€48,73 €40,27 €44,83 €37,05
You save 8%
Water alarm
€59,82 €49,44 €55,03 €45,48
You save 8%
Thermostat Ø 67 mm, 83 °C Fendt, Massey Ferguson
Ø: 67 mm. Temperature: 83 °C. More
Ø: 67 mm. Temperature: 83 °C.
€39,96 €33,03
Oil drain valve M18 x 1,5
Thread: M18 x 1.5. More
Thread: M18 x 1.5.
€68,16 €56,33 €62,71 €51,82
You save 8%
Main bearing standard Ø 85 mm
€50,48 €41,72 €46,44 €38,38
You save 8%
Intake manifold gasket Massey Ferguson, Case IH, Steyr, New Holland
Scharmüller Forced steering support plates right Ball 80 to K50 250 mm, 2 ton
Scharmüller
Assembly notes: Right. Connection position: 250 mm. Lock: K50. Colour: Black. Steering power: 2 t. Description: Approved for steering forces up to 20 ... More
Assembly notes: Right. Connection position: 250 mm. Lock: K50. Colour:...
€576,39 €476,36 €564,40 €466,45
You save 2%
Showing 49 - 89 of 89

Massey Ferguson 3640 parts for engine overhaul and hitching

Valves that no longer seat properly, a weeping crankshaft seal or a thermostat that sticks: on a Massey Ferguson 3640 with a lot of hours, the engine eventually needs work. This page has more than 90 replacement parts for the type, from GRANIT, ROCKINGER, Scharmüller, Cobo and BOSCH.

Engine, fuel and cooling

For an overhaul there are inlet valves, outlet valves, connecting rod bearings and a crankshaft seal. On the fuel side you will find injection lines, feed pump seals, sealing rings for the fuel line and a pressure switch for the fuel filter head. Cooling is covered by thermostats with matching gaskets and seals for the water circuit.

Always fit a fresh gasket with a new thermostat, even if the old one looks fine, because a flattened gasket starts dripping on the first warm day. Before fitting, hang the new thermostat in a pan of water and heat it slowly. That way you see with your own eyes that it opens before it disappears into the housing. Never bend injection lines to make them fit. A kinked or tightly bent line narrows the bore, and you notice that as a cylinder that lags behind the rest.

Drawbar, top link and forced steering

For work behind the tractor there are drawbars and trailer couplings from ROCKINGER and Scharmüller, Piton Fix parts and hydraulic top links. For trailers with forced steering you will find, among other things, a welded rod with a lock. Check the drawbar pin and the hole in the towing eye regularly. Once the pin has worn oval, replace it before play builds up in the drawbar and the wear spreads.

A hydraulic top link has the same enemy as any cylinder, which is dirt on the piston rod. Do not leave the rod extended longer than needed, and wipe it clean before retracting it. That keeps the seal intact and stops the top link from leaking. Check that the hose couplings are clean before connecting them, and fit a dust cap whenever the top link is off the tractor.

The right part for your 3640

The type plate tells you if you are really looking at a 3640. Engine parts often carry a reference number stamped by the manufacturer, and for bearings and valves that is the surest way to compare. In the Massey Ferguson line-up, the 3640 sits in the 3600 series. The Massey Ferguson 3635 and Massey Ferguson 3645 come from the same series and each have their own page, so you can see per tractor what fits. All other models from the brand are under Massey Ferguson parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison
This product has been added to your cart