Menu
EUR
Techniek Totaal Logo

We are closed today

Dear visitor!

Welcome to our site. Today is Sunday, a day of rest in the Christian religion. Therefore, we have chosen not to work today, and our webshop is closed. Of course, you are warmly welcome again tomorrow.

Have a nice Sunday and best regards,
Team Techniek Totaal

Case IH MXU 115 tractor parts & technical data

Engine components, electrics and trailer couplings for the Case IH MXU 115 are lined up here. The page holds more than 250 parts for this MXU series model.

265 parts found for Case IH MXU 115
Show:
Ball joint 75 mm, 7/8" x 14 mm, 1 1/4", taper 27 - 32 mm
A: 75 mm. C: 7/8" x 14 mm. D: 1 1/4" mm. E: 27 mm. F: 32 mm. Taper: 27 - 32 mm. More
A: 75 mm. C: 7/8" x 14 mm. D: 1 1/4" mm. E: 27 mm. F: 32 mm. Taper: 27...
€120,97 €99,98 €111,29 €91,98
You save 8%
Ball joint 95 mm, M27 x 1,5, 7/8" x 14, taper 30 - 34,6 mm
A: 95 mm. C: M27 x 1,5 mm. D: 7/8" x 14 mm. E: 30 mm. F: 34,6 mm. Taper: 30 - 34,6 mm. More
A: 95 mm. C: M27 x 1,5 mm. D: 7/8" x 14 mm. E: 30 mm. F: 34,6 mm. Tape...
€193,93 €160,27 €178,42 €147,45
You save 8%
Steering cylinder right and left ball eye-Ø 20 mm Case IH, New Holland
Technical data: Ball eye Ø: 20 mm. More
Technical data: Ball eye Ø: 20 mm.
€443,83 €366,80 €408,32 €337,46
You save 8%
GRAMMER Tractor seat Maximo Evolution Dynamic Case CVX, Steyr, New Holland
GRAMMER
To fit: Case IH, New Holland, CVX. Suspension: Air suspension. Upholstery type: Fabric / new design. Seat contact switch: Yes. Track gauge: 260 mm. Se... More
To fit: Case IH, New Holland, CVX. Suspension: Air suspension. Upholst...
€7.096,01 €5.864,47 €6.578,33 €5.436,64
You save 7%
Lift arm shaft 605 mm, Ø 30 mm Case IH, Fiat
Dimensions: Length = 605, Ø = 30 mm. More
Dimensions: Length = 605, Ø = 30 mm.
€162,07 €133,94 €149,10 €123,23
You save 8%
Scharmüller Top drawbar rail 330 mm, pin Ø 25 mm, coupling pin 31 mm
Scharmüller
Rail width: 330 mm. Detent pin Ø: 25 mm. Guide width: 32 mm. Connecting pin: 31 mm. Load capacity: 2000 kg. D-value: 82,4 kN. Colour: Black. Descript... More
Rail width: 330 mm. Detent pin Ø: 25 mm. Guide width: 32 mm. Connecti...
€1.070,65 €884,83 €1.013,17 €837,33
You save 5%
Push button switch PTO shaft with connection cable and plug
Version: Front PTO operation, Connection cable with plug. More
Version: Front PTO operation, Connection cable with plug.
€193,40 €159,83 €177,93 €147,05
You save 8%
Preheating relay 12 volt with plug connection
Version: 12 V, with plug connection. More
Version: 12 V, with plug connection.
€170,59 €140,98 €156,94 €129,70
You save 8%
PROBOSS Tractor seat AS1480 air suspended fabric 12 V, seat width 480 mm
PROBOSS
Air suspension with 12V compressor. Fore/aft isolator. Continuous height adjustment, longitudinal adjustment and backrest tilt adjustment. Mechanical ... More
Air suspension with 12V compressor. Fore/aft isolator. Continuous heig...
€842,55 €696,32
Scharmüller Drawbar 242 mm, 50 x 20 mm, ISO-50, 9,3 kN, position 1
Scharmüller
Height (mm): 20 | Mounting position: 1 | Lock: ISO-50 | D-value (kN): 9,3 | Colour: Kubota grey | Version: Standard | Width (mm): 50 | Length (mm): 24... More
Height (mm): 20 | Mounting position: 1 | Lock: ISO-50 | D-value (kN): ...
€269,09 €222,39 €247,56 €204,60
You save 8%
Steering cylinder Ford, Case IH, New Holland
€648,05 €535,58 €596,21 €492,73
You save 8%
Seal kit hydraulic steering Case IH, New Holland
€106,44 €87,97 €97,92 €80,93
You save 8%
Seal kit hydraulic steering Case IH, New Holland
€47,79 €39,50 €43,97 €36,34
You save 8%
Ball joint 106 mm, taper 20 - 22 mm, M18 x 1,5, M24 x 1,5
A: 106 mm. C: M18 x 1,5 mm. D: M24 x 1,5 mm. E: 20 mm. F: 22 mm. Taper: 20 - 22 mm. More
A: 106 mm. C: M18 x 1,5 mm. D: M24 x 1,5 mm. E: 20 mm. F: 22 mm. Taper...
€60,06 €49,64 €55,26 €45,67
You save 8%
Ball joint 125 mm, taper 24 - 27 mm, 3/4" x 16 / 1 1/8" x 16
A: 125 mm. C: 3/4" x 16 mm. D: 1 1/8" x 16 mm. E: 24 mm. F: 27 mm. Taper: 24 - 27 mm. More
A: 125 mm. C: 3/4" x 16 mm. D: 1 1/8" x 16 mm. E: 24 mm. F: 27 mm. Tap...
€64,90 €53,64 €59,71 €49,35
You save 8%
Master brake cylinder mineral oil Ø 31,4 mm Case IH, New Holland, Steyr
€277,14 €229,04 €254,97 €210,72
You save 8%
Window rubber clamping range 4 - 6 mm, 23,2 x 14,5 mm - 25 meter
Clamping range: 4 - 6 mm. Length: 25 m. B: 23,2 mm. H: 14,5 mm. More
Clamping range: 4 - 6 mm. Length: 25 m. B: 23,2 mm. H: 14,5 mm.
€225,87 €186,67 €207,80 €171,74
You save 8%
Scharmüller Adapter plate rail width 295 mm, hole pattern 140 x 80 mm, M16
Scharmüller
Load capacity: 2000 kg. D-value: 83,9 kN. Rail width: 295 mm. Hole pattern: 140 x 80 mm. Guide width: 26 mm. Plate height: 133 mm. Thread: M16. Colour... More
Load capacity: 2000 kg. D-value: 83,9 kN. Rail width: 295 mm. Hole pat...
€617,18 €510,07 €512,27 €423,37
You save 17%
Dayco Idler pulley Ø 65 mm, height 32 mm, Tector Case IH, Steyr, New Holland
Dayco
Outer Ø: 65 mm. Height: 32 mm. Installation location: Tector. More
Outer Ø: 65 mm. Height: 32 mm. Installation location: Tector.
€144,32 €119,27 €132,77 €109,73
You save 8%
Thermostat gasket Case IH, Steyr, New Holland
€33,42 €27,62 €30,75 €25,41
You save 8%
GRAMMER Tractor seat Maximo Dynamic DDS MSG95AL/741
GRAMMER
To fit: Case, New Holland, Steyr. Suspension: Air suspension. Upholstery type: Fabric. Seat contact switch: Yes. Track gauge: 260 mm. Seat width: 550 ... More
To fit: Case, New Holland, Steyr. Suspension: Air suspension. Upholste...
€3.038,64 €2.511,27
Mirror 145 x 195 mm Case IH, New Holland
Dimensions: 145 x 195 mm. Height: 195 mm. Width: 145 mm. More
Dimensions: 145 x 195 mm. Height: 195 mm. Width: 145 mm.
€58,03 €47,96 €53,39 €44,12
You save 8%
Fender bracket left complete sprung front axle with brake MXU 100-135
€451,01 €372,74 €414,93 €342,92
You save 8%
ROCKINGER Drawbar without sensor rail width 330 mm, coupling pin 30,6 mm
ROCKINGER
Colour: Black. Description: Entire coupling body and bearing forged, Easy height adjustment thanks to the use of sliding blocks, Cylindrical hitch bol... More
Colour: Black. Description: Entire coupling body and bearing forged, E...
€1.126,27 €930,80 €867,77 €717,17
You save 23%
Spiegelarm left Case IH, New Holland
€192,61 €159,18 €177,20 €146,45
You save 8%
Wiper motor windshield Case IH, New Holland
€313,64 €259,21 €288,55 €238,47
You save 8%
Loctite / Teroson Glass kit BOND 120 black - 310 ml cartridge
Loctite / Teroson
Colour: Black. Description: TEROSON® BOND 120 is a high-performance glass adhesive with a safe drive away time of 2 hours. Our new product is the per... More
Colour: Black. Description: TEROSON® BOND 120 is a high-performance g...
€29,49 €24,37
Sensor wheel speed Hall Matteffekt, connection cable with plug
Version: For speed, clutch block transmission (Hall effect), Connection cable with plug. More
Version: For speed, clutch block transmission (Hall effect), Connectio...
€116,92 €96,63 €107,57 €88,90
You save 8%
Sensor driving speed rear axle, connection cable with plug
Version: Driving speed sensor (rear axle housing), Connection cable with plug. More
Version: Driving speed sensor (rear axle housing), Connection cable wi...
€124,37 €102,79 €114,42 €94,56
You save 8%
Potentiometer rotation angle sensor EHR 4000 Ohm, 13,5 V
Version: Rotation angle sensor (position), electronic linkage control, For clutch and brake operation. More
Version: Rotation angle sensor (position), electronic linkage control,...
€151,60 €125,29 €139,47 €115,27
You save 8%
Rocker switch rear lift lifting and lowering
Version: (Rear operation) lifting and lowering. More
Version: (Rear operation) lifting and lowering.
€80,49 €66,52 €74,05 €61,20
You save 8%
LED work lights spotlight 12 W, 2359 lm, 110 x 60 x 76 mm, IP6K9K
Nominal voltage: 12 / 24 V. Voltage range: 10 - 30 V. Bulb: LED. Bulbs included: Yes. Light function: Far-reaching illumination. Dimensions W x H x D:... More
Nominal voltage: 12 / 24 V. Voltage range: 10 - 30 V. Bulb: LED. Bulbs...
€57,63 €47,63 €53,02 €43,82
You save 8%
DANA Spicer Synchro unit, complete High/Low range shift 16 x 16 and 17 x 16
€862,04 €712,43 €793,08 €655,44
You save 8%
MAHLE Gear reduction starter 12 V, 4,2 kW, 10 teeth, 245 mm, clockwise
€480,04 €396,73 €287,51 €237,61
You save 40%
Track rod A 1610 mm, B M18 x 1,5, D M18 x 1,5, E 40 mm
A: 1610 mm. B: M18 x 1,5 mm. C: 18 - 20 mm. G: . D: M18 x 1,5 mm. E: 40 mm. More
A: 1610 mm. B: M18 x 1,5 mm. C: 18 - 20 mm. G: . D: M18 x 1,5 mm. E: 4...
€187,43 €154,90 €172,44 €142,51
You save 8%
Wabco Compressor 11,5 bar, 159 cm³, Ø 75 mm, stroke 36 mm
Wabco
Operating pressure max.: 11.5 bar. Cylinder capacity: 159 cm³. Speed: 3000 1/min.. Piston Ø: 75 mm. Piston stroke: 36 mm. Cooling system: Air. Threa... More
Operating pressure max.: 11.5 bar. Cylinder capacity: 159 cm³. Speed:...
€1.893,95 €1.565,25 €1.742,43 €1.440,03
You save 8%
LUK Torsion damper PTO shaft 8 teeth, 31,9 x 35
LUK
Number of teeth: 8. Tooth profile: 31.9x35. More
Number of teeth: 8. Tooth profile: 31.9x35.
€267,68 €221,22 €246,27 €203,53
You save 8%
LUK Torsion damper 16 teeth, tooth profile 31X35 Case IH, Steyr, New Holland
LUK
Number of teeth: 16. Tooth profile: 31x35. Menke no.: 92343. More
Number of teeth: 16. Tooth profile: 31x35. Menke no.: 92343.
€765,95 €633,02 €704,67 €582,38
You save 8%
Brake lining hand brake lining on one side Case IH, Steyr, New Holland
ROCKINGER Drawbar without sensor rail 336 mm, coupling pin 38 mm, black
ROCKINGER
Rail width: 336 mm. Detent pin Ø: 22 mm. Guide width: 30 mm. Connecting pin: 38 mm. Load capacity: 2000 kg. D-value: 120,0 kN. Colour: Black. Descrip... More
Rail width: 336 mm. Detent pin Ø: 22 mm. Guide width: 30 mm. Connecti...
€1.088,39 €899,50 €838,59 €693,05
You save 23%
GRAMMER Seat Maximo Professional MSG95AL/731, 530 mm
GRAMMER
To fit: Case CVX, Steyr, New Holland. Suspension: Air suspension. Upholstery type: Fabric. Seat contact switch: Yes. Track gauge: 260 mm. Seat width: ... More
To fit: Case CVX, Steyr, New Holland. Suspension: Air suspension. Upho...
€2.506,09 €2.071,15
VICTOR REINZ Valve cover gasket Case IH, Steyr, New Holland
Tank cap thread 45 mm, for expansion tank
Version: Thread: 45 mm, For expansion tank. More
Version: Thread: 45 mm, For expansion tank.
€16,78 €13,86
Radiator Steyr Profi, New Holland TS, Case IH Farmall, MXU
To fit as: Steyr Serie Profi (4100–6140 Tier 3 and Classic, with or without Serial No Z*BF60001, years 2003–2011), Serie Profi CVT (4110, 4120, 41... More
To fit as: Steyr Serie Profi (4100–6140 Tier 3 and Classic, with or ...
€989,09 €817,43 €909,96 €752,04
You save 8%
Cylinder head gasket 1,15 mm engine Iveco F4D Case IH, New Holland, Steyr
€245,30 €202,73 €225,68 €186,51
You save 8%
Air hose intercooler inner-Ø 57 mm, length 90 mm
Inner Ø: 57 mm. Length: 90 mm. More
Inner Ø: 57 mm. Length: 90 mm.
€43,60 €36,03 €40,11 €33,15
You save 8%
Belt kit 1550 mm, 8 ribs, belt tensioner
Version: For main belt drive. Contents: Belt, belt tensioner. Belt length: 1550 mm. Ribs: 8 n. More
Version: For main belt drive. Contents: Belt, belt tensioner. Belt len...
€47,54 €39,29 €43,74 €36,15
You save 8%
Showing 97 - 144 of 265

Case IH MXU 115 parts

If the driveline of your MXU 115 rattles at idle or clunks as the clutch takes up, the torsion damper between engine and transmission deserves a look first. It is one of more than 250 new replacement parts for this Case IH on this page, from GRANIT, Scharmüller, ROCKINGER, GRAMMER, PROBOSS and others.

Torsion damper and linkage seals

Replacing the torsion damper means splitting the tractor. While it is apart, inspect the splines on the shaft the damper slides onto. Worn splines will wear out a new damper early.

For the rear linkage there are lift arm shaft seals and complete seal kits. If oil is weeping from the lift arm shaft, clean the shaft and feel for a groove where the old seal ran. A new seal on a grooved shaft soon leaks again. Always fit the lip facing the oil. Separate sealing rings and ball joints for the front axle complete this area. Play in a ball joint shows up quickest when someone rocks the steering wheel while you watch the front wheel.

A leaking linkage seal kit often shows itself before oil appears on the floor, as an implement slowly sinks while the tractor is parked. Replace the full kit in one go, otherwise the neighbouring ring will start leaking a few months later. Deburr sharp edges on grooves and bores before fitting, and cycle the lift fully a few times afterwards before checking the oil level.

Hitching up

For the back end there are ROCKINGER automatic hitches, drawbar retrofit kits, height adjustable adapter plates and the Scharmüller Piton Fix system, so the hitch can be set up for the job in hand.

Seat and cab

Long days call for a decent seat. There are GRAMMER tractor seats from the Maximo line and air suspended PROBOSS seats, some with a seat heater. Mirrors, gas struts, rocker switches and sensors for the electronics complete the cab side.

Matching parts to your MXU

The type plate tells you which model you have. Look for a reference number on the old part and compare it with the number shown with the product. Before ordering a hitch or adapter plate, measure the rail width on the drawbar frame.

Running another MXU alongside the 115? Each of these models has a page of its own:

All other tractors of the brand are listed under Case IH parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison
This product has been added to your cart