Menu
EUR

John Deere 6020 tractor parts & technical data

A wide range of more than 500 parts fits the John Deere 6020. This page covers trailer couplings, electrics, and steering and front axle components.

501 parts found for John Deere 6020
Show:
GRANIT Internal plate reversing clutch 3,1 mm, inner 240 mm, outer 294 mm
GRANIT
Version: Thickness: 3.1 mm Inner: 240 mm Outer: 294 mm More
Version: Thickness: 3.1 mm Inner: 240 mm Outer: 294 mm
€76,96 €63,60 €73,10 €60,41
You save 5%
GRANIT External plate thickness 7 mm, inner 140 mm, outer 251 mm
GRANIT
Version: thickness = 7 mm inner = 140 mm outer = 251 mm | Menke no.: 221658 More
Version: thickness = 7 mm inner = 140 mm outer = 251 mm | Menke no.: 2...
€131,50 €108,68 €124,90 €103,22
You save 5%
DANA Spicer Ball joint 285 mm, M20 x 1,5 / M26 x 1,5, taper 23,66 - 26,2 mm
€250,12 €206,71 €237,60 €196,36
You save 5%
DANA Spicer Differential bevel gear final drive front axle 730
€234,30 €193,64 €222,55 €183,93
You save 5%
DANA Spicer Joint final drive front axle 730 John Deere
€1.455,90 €1.203,22
Scharmüller Forced steering 250 mm, K50, right, 2 ton, black, 11,23 kg
Scharmüller
Description: Approved for steering forces up to 20 kN (2 t) | Connection position: 250 mm | Steering power (t): 2 | Colour: Black | Lock: K50 | Assemb... More
Description: Approved for steering forces up to 20 kN (2 t) | Connecti...
€612,85 €506,49
FEBI Hydraulic oil filter HF35474
€59,76 €49,39 €39,31 €32,49
You save 34%
FEBI Alternator 14 V / 150 A, form B, flange 56,0 mm
FEBI
To fit as: Fendt, Hürlimann, Lamborghini, Same More
To fit as: Fendt, Hürlimann, Lamborghini, Same
€435,60 €360,00 €247,81 €204,80
You save 43%
HELLA Starter motor 12 V, 3 kW, 11 teeth, Ø 83 mm, clockwise
€790,40 €653,22 €635,45 €525,17
You save 20%
GRANIT Axial joint 211 mm, M26 x 1,5, M24 x 1,5, Ø 56 mm, Ø 40 mm
GRANIT
A: 211 mm. C: M26 x 1,5 mm. D: M24 x 1,5 mm. Ø B: 56 mm. Ø E: 40 mm. More
A: 211 mm. C: M26 x 1,5 mm. D: M24 x 1,5 mm. Ø B: 56 mm. Ø E: 40 mm.
€129,54 €107,06 €123,00 €101,65
You save 5%
GRANIT Axial joint right and left 216 mm, M26 x 1,5, M24 x 1,5, Ø 56 mm
GRANIT
A: 216 mm. C: M26 x 1,5 mm. D: M24 x 1,5 mm. Ø B: 56 mm. Ø E: 40 mm. More
A: 216 mm. C: M26 x 1,5 mm. D: M24 x 1,5 mm. Ø B: 56 mm. Ø E: 40 mm.
€125,60 €103,80
Ball joint right 258 mm, taper 24,6 - 28,5 mm, M22 x 1,5, M24 x 1,5
A: 258 mm. C: M22 x 1,5 mm. D: M24 x 1,5 mm. E: 24,6 mm. F: 28,5 mm. Taper: 24,6 - 28,5 mm. More
A: 258 mm. C: M22 x 1,5 mm. D: M24 x 1,5 mm. E: 24,6 mm. F: 28,5 mm. T...
€95,13 €78,62 €90,35 €74,67
You save 5%
GRANIT Bearing with housing torsion damper outer-Ø 34 mm John Deere
GRANIT
Outer Ø: 34 mm. Hole Ø: 12 mm. Inner Ø: 30 mm. More
Outer Ø: 34 mm. Hole Ø: 12 mm. Inner Ø: 30 mm.
€102,49 €84,70 €97,35 €80,45
You save 5%
MAHLE Expansion tank 464 x 297 x 267 mm, 1,25 l, 0,8 bar John Deere
MAHLE
Length: 464 mm. Width: 297 mm. Depth: 267 mm. Opening pressure: 0,8 bar. Contents: 1,25 l. Material: Plastic. Technical data: With screw cap. More
Length: 464 mm. Width: 297 mm. Depth: 267 mm. Opening pressure: 0,8 ba...
€206,06 €170,30 €128,75 €106,41
You save 38%
GRANIT Heating element John Deere Engine 6068, Se 6930
€271,17 €224,11 €257,60 €212,89
You save 5%
VICTOR REINZ Air receiver gasket John Deere
€3,52 €2,91
GRANIT Clamp exhaust Ø 91 mm, width 18,4 mm John Deere
GRANIT
Ø: 91 mm. Width: 18,4 mm. More
Ø: 91 mm. Width: 18,4 mm.
€66,51 €54,97 €63,15 €52,19
You save 5%
GRANIT Vibration damper John Deere
Showing 241 - 264 of 501

John Deere 6020 parts for steering, front axle and electrics

Steering play on a John Deere 6020 is something you feel on every road trip, and it is often the first job that needs attention on a tractor of this type. This page carries more than 500 parts for the 6020, supplied by GRANIT, ROCKINGER, Sauermann, Scharmüller and HELLA.

Ball joints and the ZF front axle

Ball joints for the steering are available in several versions. When fitting one, make sure the taper and its seat in the steering knuckle are clean, dry and without grease, and secure the nut with a new split pin. For the ZF front axle there are external and internal plates, plus bushes, for example for the balancer shaft. Plates are always replaced as a full set and soaked in the correct oil before assembly. The ZF number is often stamped on the old plate itself.

Charging and switching

Alternators, relays and micro relays with changeover contacts keep the electrical system running. Before you replace an alternator, measure the charging voltage with the engine running and check the belt and earth connection. A relay is easiest to test by swapping it with an identical one from another circuit. If the fault moves with it, you have found the culprit. If the alternator is not charging, look at the heavy charge cable to the battery as well. A corroded terminal produces the same symptoms as a failed regulator and is cured with a wire brush and a little terminal grease.

Seals, hoses, seats and hitch

O-rings, gaskets and seals cover many positions, from the regulator housing gasket to the O-ring for the tank sender. Hoses are part of the range as well. In the cab there are tractor seats, including air suspended Maximo models. At the rear you will find drawbars, drawbar frames and forced steering units for trailers with a steered axle.

Making sure the part fits

The type plate shows the model and serial number. The serial number matters because parts can change over the production run of a single model. The reference number on the old part is the final check, so compare it with the product description before ordering.

Other tractors in the same family each have their own page, so you only see what fits that particular type:

The 6520, the 6420S and every other John Deere model are reachable through the overview of John Deere parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart