Menu
EUR

John Deere 6510 tractor parts & technical data

The John Deere 6510 from the 6010/6010SE range is well covered here, with more than 600 parts in groups such as lighting, trailer couplings and electrics.

645 parts found for John Deere 6510
Show:
GRANIT Sealing washer filler neck Ø 70 x 4,5 mm John Deere
GRANIT
Dimensions: Ø 70 x 4.5 mm. Description: For filler neck. More
Dimensions: Ø 70 x 4.5 mm. Description: For filler neck.
€12,90 €10,66
Ball bearing fan drive Ø 25,4 x 47,6 x 70 mm John Deere
Ø: 25,4 x 47,6 x 70 mm. Shaft length: 123,5 mm. Description: For fan drive. More
Ø: 25,4 x 47,6 x 70 mm. Shaft length: 123,5 mm. Description: For fan ...
€91,51 €75,63 €86,90 €71,82
You save 5%
GRANIT Tensioning pulley Ø 78 / 31 mm John Deere 5070M-5100M, 6010-6920
GRANIT
Outer Ø: 78 mm. Width: 31 mm. Menke no.: 221661. More
Outer Ø: 78 mm. Width: 31 mm. Menke no.: 221661.
€64,87 €53,61 €61,60 €50,91
You save 5%
GRANIT Radiator hose, bottom inner-Ø 60 / 52 mm John Deere
GRANIT
Inner Ø: 60 / 52 mm. More
Inner Ø: 60 / 52 mm.
€31,67 €26,17 €30,00 €24,79
You save 5%
GRANIT Tank cap reservoir grommet-Ø 45 mm
GRANIT
Version: For expansion tank. Neck Ø: 45 mm. More
Version: For expansion tank. Neck Ø: 45 mm.
€8,65 €7,15
Optibelt Multi-rib belt John Deere 5090M, 5100R, 5820, 6130-6630, chopper 7250
€81,19 €67,10 €77,10 €63,72
You save 5%
Optibelt Multi-rib belt 8 ribs John Deere, Massey Ferguson
€67,19 €55,53 €63,80 €52,73
You save 5%
Optibelt Powerband multi-rib belt 8 ribs John Deere 5090M, 5100R, 6130-7330
€81,17 €67,08 €77,10 €63,72
You save 5%
Exhaust pipe John Deere 6510-6910S, SE6510, SE6610
€139,40 €115,21 €132,40 €109,42
You save 5%
GRANIT Valve stem seal John Deere
€10,45 €8,64
Gasket set, complete engine 6068 Powertech John Deere
Version: The cylinder head gasket is a multi-layer steel gasket.. Assembly notes: Tightening instructions for cylinder head bolts:, Step 1: first tigh... More
Version: The cylinder head gasket is a multi-layer steel gasket.. Asse...
€317,85 €262,69
Crankshaft seal for Ø 55,4 x 84 x 14,5 mm John Deere
Outer Ø: 84 mm. Width: 14,5 mm. Inner Ø: 55,4 mm. More
Outer Ø: 84 mm. Width: 14,5 mm. Inner Ø: 55,4 mm.
€39,00 €32,23
O-ring oil pump 24,994 x 3,531 mm John Deere
Dimensions: 24.994 x 3.531 mm. More
Dimensions: 24.994 x 3.531 mm.
€4,26 €3,52
GRANIT Thrust bearing John Deere
€36,26 €29,97 €34,40 €28,43
You save 5%
GRANIT Intake gasket inner Ø 54,5 mm, hole spacing 87 mm John Deere, Renault
GRANIT
Dimensions: innen Ø54,5 mm, Lochabstand 87 mm, Schrauben Ø 11 mm. More
Dimensions: innen Ø54,5 mm, Lochabstand 87 mm, Schrauben Ø 11 mm.
€2,94 €2,43
Crankshaft seal rear Ø 117,8 x 146,25 x 13,8 mm John Deere, Renault
Showing 337 - 360 of 645

John Deere 6510 parts

More than 600 parts are matched to the John Deere 6510 on this page, from GRANIT, HELLA, ROCKINGER, Scharmüller and Wabco. They run from an oil pump O-ring to a cab hinge, and a few groups stand out for this tractor.

Cab doors and hinges

A cab door that drops, will not stay open or rattles over rough ground usually comes down to tired gas struts or a worn hinge. For the 6510 there are door gas struts and cab hinges. Change gas struts with the door held open by a helper or a prop, and fit the new strut with the rod pointing down so its seal stays lubricated. If the hinge pin has worn, the door will sit low and the lock will not line up, which is worth fixing before the seals on the door frame start to suffer.

Engine cooling and belts

  • thermostats and gaskets for the thermostat housing
  • hoses
  • multi-rib belts
  • O-rings, including one for the oil pump
  • alternators and micro relays
  • HELLA headlights

When fitting a new thermostat, always renew the gasket and clean both mating faces thoroughly, since a scrap of old gasket is enough to cause a leak.

Front axle, steering and hitch

The 6510 also has external and internal plates for the front axle, parts for forced steering with ball ends on both sides, and automatic drawbars and drawbar frames from ROCKINGER and Scharmüller. Replace axle plates as a set and on both sides together, keeping external and internal plates in the order they came out.

Confirming the fit

The rating plate tells you it is a 6510. For O-rings, gaskets and plates, the reference number on the old part settles it. If it is unreadable, lay old and new side by side and compare shape, holes and thickness.

With forced steering, the ball ends on both sides are under real load, especially on tight headland turns. Check them for play regularly by rocking the rod by hand, and replace any ball end with play straight away, before it lets the trailer wander and wears the rest of the system.

Other tractors in the 6010 series

The 6510 is part of the John Deere 6010 series, and other tractors from that range have their own page: John Deere 6010, John Deere 6110, John Deere 6210, John Deere 6410 and John Deere 6810. Order for each type from its own page. Running another model from this maker? Browse the overview of John Deere parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart