Menu
EUR

John Deere 1550 tractor parts & technical data

More than 550 parts fit the John Deere 1550. From lighting and electrics to trailer couplings, everything is gathered here so you can skip the long search.

555 parts found for John Deere 1550
Show:
Collet set John Deere
Valve seat steering valve John Deere 830-3650
Menke no.: 221649. More
Menke no.: 221649.
€37,09 €30,65 €35,20 €29,09
You save 5%
GRANIT Toothed rack steering valve John Deere 830-3650
€130,83 €108,12 €124,25 €102,69
You save 5%
GRANIT Drive shaft steering valve John Deere 830-3650
€95,12 €78,61 €90,35 €74,67
You save 5%
GRANIT Parts set hydraulic pump John Deere 830-3650
€279,51 €231,00 €265,50 €219,42
You save 5%
Seal kit hydraulic pump John Deere 830-3650
Menke no.: 221636. More
Menke no.: 221636.
€66,91 €55,30 €63,55 €52,52
You save 5%
GRANIT Door lock, right John Deere MC 1, Series 40-2850
€94,14 €77,80 €89,40 €73,88
You save 5%
Shim 29 x 42 x 1,2 mm John Deere 1350-3650
Dimensions: 29 x 42 x 1.2 mm. More
Dimensions: 29 x 42 x 1.2 mm.
€2,50 €2,07
GRANIT Bush 28 x 47 x 24,5 mm John Deere 1350-3650
GRANIT
Dimensions: 28 x 47 x 24.5 mm. Menke no.: 221654. More
Dimensions: 28 x 47 x 24.5 mm. Menke no.: 221654.
€42,50 €35,12 €40,35 €33,35
You save 5%
Lifting strut complete left 560 - 760 mm, eye-Ø 19,5 mm John Deere
Dimensions: Length = 560 - 760, Eye Ø = 19.5 mm. More
Dimensions: Length = 560 - 760, Eye Ø = 19.5 mm.
€406,56 €336,00 €386,20 €319,17
You save 5%
GRANIT Spring hood John Deere 820-3640
GRANIT Cover John Deere 1350-3650
€34,30 €28,35
GRANIT Ball for gear shift linkage Ø 12,7 mm, 1/2 inch, DIN 5401
GRANIT
Ø Dw: 12,7 mm. Ø Dw: 1/2 inches. DIN: DIN 5401. More
Ø Dw: 12,7 mm. Ø Dw: 1/2 inches. DIN: DIN 5401.
€4,09 €3,38
Oil pressure switch brake system M10 x 1,0 conical
Version: Thread: M10 x 1.0 tapered. More
Version: Thread: M10 x 1.0 tapered.
€53,80 €44,46 €48,65 €40,21
You save 10%
GRANIT Battery cut-off switch knob 12 V, 100 A, 2 x M10, with key
GRANIT
Version: Rotary operation, removable key with splash protection cap Connection thread: 2x M10 Power rating at 12 V: 100 A. Connection thread: M10. Cur... More
Version: Rotary operation, removable key with splash protection cap Co...
€54,63 €45,15 €49,40 €40,83
You save 10%
HELLA Headlight left / right 12 V, H4, built-in, glass 164 x 103 mm
HELLA
Bulb: 12V60/55W / H4. Installation location: Left/right. Nominal voltage: 12 V. Test mark: E1 44504, ECE. Light function: With dipped beam, with full ... More
Bulb: 12V60/55W / H4. Installation location: Left/right. Nominal volta...
€105,75 €87,40
Showing 265 - 288 of 555

John Deere 1550 parts

More than 550 parts fit the John Deere 1550, enough to take care of a full service in one go, from the clutch to the headlights. Brands include GRANIT, HELLA, MAHLE, LUK and Wabco.

Clutch

For the clutch there are clutch plates with a torsion damper and single clutch pressure plates. Replace the plate and pressure plate together where you can. The tractor has to be split either way, and a new plate running against a worn pressure plate will not last. While it is apart, inspect the flywheel too: scoring or blue heat marks should be skimmed out before the new plate goes in.

Engine, cooling and electrics

  • Water pumps, plus seals for the lift pump and the coolant circuit
  • Exhaust gaskets and a lift housing gasket
  • O-rings, including one for the brake master cylinder
  • Starter motors and alternators
  • Left and right headlights

Coolant seeping from the weep hole on the water pump means the shaft seal has gone and the pump will not last much longer. Replace it as a unit and clean the gasket faces on the block thoroughly. Look over the belt and hoses at the same time, then refill with fresh coolant. Warm the engine up with the heater valve open and top up as the level drops. Headlights are available separately for left and right, so only the damaged side needs replacing.

Linkage, steering and air brakes

Lift arm bushes and washers take the play out of the rear linkage. On the steering side you can replace track rods and ball joints. Connector heads cover the air brake supply to a trailer, and gas struts hold the cab door or window where they should.

When changing a track rod, measure the old one first so the toe setting stays roughly where it was, then have the alignment checked, since wrong toe wears front tyres quickly.

Making sure it fits

First confirm on the data plate that the tractor is a 1550. Some parts are made for a group of John Deere models, such as a lift housing gasket that fits from the 820 up to the 3650 and a pressure plate for the 840 up to the 2650. The product details show this. Also compare the number on the old part, especially for the clutch, where the spline count and plate diameter have to match.

The 1550 is part of the 50 series. Two other tractors from that series have pages of their own:

For any other John Deere you look after, go to the overview of John Deere parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart