Menu
EUR

John Deere 1550 tractor parts & technical data

More than 550 parts fit the John Deere 1550. From lighting and electrics to trailer couplings, everything is gathered here so you can skip the long search.

555 parts found for John Deere 1550
Show:
GRANIT Clamp injection nozzle John Deere 820-4050, 925-1177
GRANIT
Description: For injection nozzle. More
Description: For injection nozzle.
€31,55 €26,07
GRANIT Vibration damper John Deere 1640-2140
GRANIT Radiator cap
€20,95 €17,31
GRANIT Radiator hose, bottom inner-Ø 44 mm John Deere
GRANIT
Inner Ø: 44 mm. More
Inner Ø: 44 mm.
€19,10 €15,79
GRANIT Thermostat Ø 54 mm, 82 °C John Deere, JCB
GRANIT
Ø: 54 mm. Temperature: 82 °C. More
Ø: 54 mm. Temperature: 82 °C.
€28,70 €23,72
GRANIT Top gasket set with meerlagige steel gasket John Deere
GRANIT
Version: The cylinder head gasket is a multi-layer steel gasket.. Assembly notes: Tightening instructions for cylinder head bolts:, Step 1: first tigh... More
Version: The cylinder head gasket is a multi-layer steel gasket.. Asse...
€226,96 €187,57 €215,60 €178,18
You save 5%
Piston ring set Ø 106,5 mm, 3 mm trapezoidal ring / 2,4 mm / 3,5 mm
Dimensions: 3 rings, Ø 106.5 mm, 3 mm (trapezoidal ring) / 2.4 mm / 3.5 mm. More
Dimensions: 3 rings, Ø 106.5 mm, 3 mm (trapezoidal ring) / 2.4 mm / 3...
€43,62 €36,05 €41,40 €34,21
You save 5%
GRANIT O-ring cylinder head Ø 18,72 x 2,61 mm John Deere
GRANIT
Description: Ø 18.72 x 2.61 mm. More
Description: Ø 18.72 x 2.61 mm.
€2,71 €2,24
GRANIT Silencer vertical 775 mm, inner Ø 62 mm, exhaust Ø 48 mm
GRANIT
Version: Length: 775 mm, Inner Ø: 62 mm, Outlet Ø: 48 mm. More
Version: Length: 775 mm, Inner Ø: 62 mm, Outlet Ø: 48 mm.
€116,60 €96,36 €110,75 €91,53
You save 5%
Main bearing standard Ø 80 mm John Deere, Renault
Dimensions: Ø 80 mm. Menke no.: 59705. More
Dimensions: Ø 80 mm. Menke no.: 59705.
€26,90 €22,23
GRANIT Push rod John Deere
€30,50 €25,21
GRANIT Silencer horizontal John Deere 820-1850N
€272,70 €225,37 €259,00 €214,05
You save 5%
GRANIT Union nut return line John Deere
GRANIT Sealing washer return line outer-Ø 10,5 mm, inner-Ø 5,6 mm
GRANIT
Dimensions: Height 5.4 <lt>br<gt> Outer Ø 10.5 <lt>br<gt> Inner Ø 5.6</gt></lt></gt></lt> mm. Outer Ø: 10,5 mm. Height: 5,4 mm. Inner Ø: 5,6 mm. M... More
Dimensions: Height 5.4 <lt>br<gt> Outer Ø 10.5 <lt>br<gt> Inner Ø 5....
€2,40 €1,98
Oil cooler 9 cooling plates John Deere
€239,28 €197,75 €227,30 €187,85
You save 5%
GRANIT Flange hydraulic pump drive shaft 198 John Deere series 40-50
€205,10 €169,50 €194,80 €160,99
You save 5%
Showing 433 - 456 of 555

John Deere 1550 parts

More than 550 parts fit the John Deere 1550, enough to take care of a full service in one go, from the clutch to the headlights. Brands include GRANIT, HELLA, MAHLE, LUK and Wabco.

Clutch

For the clutch there are clutch plates with a torsion damper and single clutch pressure plates. Replace the plate and pressure plate together where you can. The tractor has to be split either way, and a new plate running against a worn pressure plate will not last. While it is apart, inspect the flywheel too: scoring or blue heat marks should be skimmed out before the new plate goes in.

Engine, cooling and electrics

  • Water pumps, plus seals for the lift pump and the coolant circuit
  • Exhaust gaskets and a lift housing gasket
  • O-rings, including one for the brake master cylinder
  • Starter motors and alternators
  • Left and right headlights

Coolant seeping from the weep hole on the water pump means the shaft seal has gone and the pump will not last much longer. Replace it as a unit and clean the gasket faces on the block thoroughly. Look over the belt and hoses at the same time, then refill with fresh coolant. Warm the engine up with the heater valve open and top up as the level drops. Headlights are available separately for left and right, so only the damaged side needs replacing.

Linkage, steering and air brakes

Lift arm bushes and washers take the play out of the rear linkage. On the steering side you can replace track rods and ball joints. Connector heads cover the air brake supply to a trailer, and gas struts hold the cab door or window where they should.

When changing a track rod, measure the old one first so the toe setting stays roughly where it was, then have the alignment checked, since wrong toe wears front tyres quickly.

Making sure it fits

First confirm on the data plate that the tractor is a 1550. Some parts are made for a group of John Deere models, such as a lift housing gasket that fits from the 820 up to the 3650 and a pressure plate for the 840 up to the 2650. The product details show this. Also compare the number on the old part, especially for the clutch, where the spline count and plate diameter have to match.

The 1550 is part of the 50 series. Two other tractors from that series have pages of their own:

For any other John Deere you look after, go to the overview of John Deere parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart