Menu
EUR
Techniek Totaal Logo

We are closed today

Dear visitor!

Welcome to our site. Today is Sunday, a day of rest in the Christian religion. Therefore, we have chosen not to work today, and our webshop is closed. Of course, you are warmly welcome again tomorrow.

Have a nice Sunday and best regards,
Team Techniek Totaal

Deutz D 7007 tractor parts & technical data

If the lights on your Deutz D 7007 have failed or the electrics are playing up, this page lists more than 200 parts that fit this 07 series tractor.

214 parts found for Deutz-Fahr D 7007
Show:
Sealing ring lift shaft left 75 x 90 x 10 mm, NBR Deutz-Fahr
Dimensions: 75 x 90 x 10 mm. Material: NBR. More
Dimensions: 75 x 90 x 10 mm. Material: NBR.
€37,94 €31,36 €34,90 €28,85
You save 8%
Brake light switch mechanical M14 x 1, break contact, blade terminal 6,3 mm
Version: Thread M14 x 1, break contact, normally on, Blade terminals 6.3 mm. Menke no.: 80803. More
Version: Thread M14 x 1, break contact, normally on, Blade terminals 6...
€36,91 €30,51
HELLA Starter motor 12 V, 3,0 kW, 9 teeth, mounting Ø 89 mm, clockwise
€595,84 €492,43 €459,08 €379,41
You save 23%
Track rod telescopic axle, hydraulic steering A 1230 - 1740 mm
A: 1230 - 1740 mm. C: 20 - 22 mm. G: . More
A: 1230 - 1740 mm. C: 20 - 22 mm. G: .
€741,22 €612,58 €681,92 €563,57
You save 8%
LUK Pilot bearing 20 x 52 x 15 mm
LUK
Dimensions: 20 x 52 x 15 mm. More
Dimensions: 20 x 52 x 15 mm.
€32,83 €27,13 €30,20 €24,96
You save 8%
Repair set brake cylinder without piston Deutz AgroStar 4.61-6.61
Additional information: Without piston. More
Additional information: Without piston.
€48,28 €39,90 €44,42 €36,71
You save 8%
Wheel brake cylinder Ø 38,1 mm, rear, drum brake, DOT 4 Deutz-Fahr
€420,66 €347,65 €387,01 €319,84
You save 8%
PTO shaft end piece 265 mm, 1 3/8 inch 6 splines, 540 rpm
Version: Length 265 mm, 1 3/8", 6 splines, for 540 rpm. More
Version: Length 265 mm, 1 3/8", 6 splines, for 540 rpm.
€657,50 €543,39 €604,90 €499,92
You save 8%
VICTOR REINZ Crankshaft seal for Ø 65 x 85 x 10,5 mm engine FL912, FL913 Deutz-Fahr
€37,37 €30,88 €34,38 €28,41
You save 8%
VICTOR REINZ Crankshaft seal rear Fendt, Deutz-Fahr
€42,88 €35,44 €39,45 €32,60
You save 8%
Bush for fan Deutz-Fahr
Exhaust manifold Deutz-Fahr D 4007 - D 7207, D 4507C - D 7807C
€173,62 €143,49 €159,73 €132,01
You save 8%
Piston ring set 4 rings, Ø 100 mm Fendt, Deutz-Fahr
Dimensions: 4 rings, Ø 100 mm, 3 mm (trapezoidal ring) / 2.5 mm / 2.5 mm / 5 mm. More
Dimensions: 4 rings, Ø 100 mm, 3 mm (trapezoidal ring) / 2.5 mm / 2.5...
€43,73 €36,14 €40,23 €33,25
You save 8%
O-ring oil pump 14,5 x 3 mm Fendt, Renault, Deutz-Fahr
Dimensions: 14.5 x 3 mm. More
Dimensions: 14.5 x 3 mm.
€8,25 €6,82
Valve spring engine F2L912-F6L913, BF6L913 Deutz-Fahr, Fendt
Engine types: F2L912, F3L912, F4L912, F6L912, F4L913, F6L913, BF6L913. More
Engine types: F2L912, F3L912, F4L912, F6L912, F4L913, F6L913, BF6L913.
€11,95 €9,88
Thrust washer rear thickness 2,94 mm Deutz-Fahr
Engine types: FL912. Dimensions: Thickness 2.94 mm. More
Engine types: FL912. Dimensions: Thickness 2.94 mm.
€18,08 €14,94
Connecting rod bush Ø 35 mm Fendt, Deutz-Fahr
Dimensions: Ø 35 mm. More
Dimensions: Ø 35 mm.
€9,33 €7,71
Shim 0,5 mm liner Bottom, Ø 117,6 x 112 mm Fendt, Deutz-Fahr
Outer Ø: 117,6 mm. Inner Ø: 112 mm. Material: Steel. Thickness: 0,5 mm. More
Outer Ø: 117,6 mm. Inner Ø: 112 mm. Material: Steel. Thickness: 0,5 ...
€3,59 €2,96
Shim cylinder liner 0,2 mm, Ø 117,6 x 110,1 mm Deutz-Fahr
Outer Ø: 117,6 mm. Inner Ø: 110,1 mm. Material: Steel. Thickness: 0,2 mm. More
Outer Ø: 117,6 mm. Inner Ø: 110,1 mm. Material: Steel. Thickness: 0,...
€2,83 €2,33
Cylinder head gasket set engine FL912, FL913, BFL913 Fendt, Deutz-Fahr, Linde
Engine types: FL912, FL913, BFL913. Supplementary set: For one cylinder head. Additional information: Without cylinder head gasket. More
Engine types: FL912, FL913, BFL913. Supplementary set: For one cylinde...
€19,35 €15,99
Oil pump thread 28 x 1,5 mm Fendt, Renault, Deutz-Fahr
Dimensions: Thread 28 x 1.5 mm. More
Dimensions: Thread 28 x 1.5 mm.
€116,47 €96,26 €107,15 €88,56
You save 8%
Connecting rod bearing standard, Ø 60 mm, width 25 mm Fendt, Deutz-Fahr
Engine types: FL812, FL912. Dimensions: Ø 60 mm. More
Engine types: FL812, FL912. Dimensions: Ø 60 mm.
€10,94 €9,04
Main bearing standard Ø 70 mm Fendt, Deutz-Fahr
Engine types: FL812, FL912. Dimensions: 4. More
Engine types: FL812, FL912. Dimensions: 4.
€16,99 €14,04
Valve seat ring outlet valve Fendt, Deutz-Fahr
Engine types: F2L912, F3L912, F4L912, F6L912, F4L913, F6L913, BF6L913. More
Engine types: F2L912, F3L912, F4L912, F6L912, F4L913, F6L913, BF6L913.
€28,38 €23,45
Bolt set 3de steering valve M10 x 190 Deutz-Fahr
Technical data: M10 x 190. More
Technical data: M10 x 190.
€36,94 €30,53
Bolt set 2de steering valve 1x M8 x 140, 2x M8 x 130 Deutz-Fahr
Technical data: consisting of: 1 x M8 x 140, 2 x M8 x 130, for 2nd Control unit. More
Technical data: consisting of: 1 x M8 x 140, 2 x M8 x 130, for 2nd Con...
€33,59 €27,76
Bolt set 1ste steering valve M10 x 100 Deutz-Fahr
Technical data: M10 x 100. More
Technical data: M10 x 100.
€16,33 €13,49
Steering valve dw not blocked 210 bar, 70 l/min, system SD60
Technical data: Max. operating pressure: 210 bar, Nominal flow rate: max. 70 l/min., Operating material: hydraulic oil, Tightening torque: 30 Nm, Conn... More
Technical data: Max. operating pressure: 210 bar, Nominal flow rate: m...
€663,73 €548,54 €610,63 €504,65
You save 8%
Single pump 16,8 cm³/rpm., taper 1:5, Ø 17 x 17, left
Output volume: 16,8 cc/rev. Drive shaft: Taper 1:5, Ø 17 x 17. A: 45 mm. B: 107,5 mm. Direction of rotation: Anticlockwise. Line connection suction s... More
Output volume: 16,8 cc/rev. Drive shaft: Taper 1:5, Ø 17 x 17. A: 45 ...
€232,74 €192,35 €214,12 €176,96
You save 8%
Leaf spring linkage reinforced Deutz-Fahr
€319,45 €264,01 €293,89 €242,89
You save 8%
Sealing ring piston 88 x 3 mm Deutz-Fahr
Dimensions: 88 x 3 mm. More
Dimensions: 88 x 3 mm.
€36,14 €29,87
Sealing ring piston 70 x 89 x 12 mm Deutz-Fahr
Dimensions: 70 x 89 x 12 mm. More
Dimensions: 70 x 89 x 12 mm.
€40,97 €33,86 €37,69 €31,15
You save 8%
Lift rod 680 - 880 mm, ball joint-Ø 28,4 mm Deutz-Fahr
Dimensions: Length = 680 - 880, Ball joint Ø = 28.4, Clevis Ø = 20, Internal dimension of clevis = 25 mm. More
Dimensions: Length = 680 - 880, Ball joint Ø = 28.4, Clevis Ø = 20, ...
€221,91 €183,40 €204,16 €168,73
You save 8%
Pin top link tractor side cat. 2, Ø 25 mm Deutz-Fahr
Dimensions: Ø: 25 mm. More
Dimensions: Ø: 25 mm.
€35,67 €29,48 €32,82 €27,12
You save 8%
Drive shaft 2100 mm, 2x M18 x 1,5
Version: Thread: 2 x M18 x 1.5. More
Version: Thread: 2 x M18 x 1.5.
€132,45 €109,46 €121,85 €100,71
You save 8%
Adaptor for
€69,95 €57,81 €64,35 €53,19
You save 8%
HELLA Indicator / position light right IHC, Deutz-Fahr, Fendt, Kubota
HELLA
To fit as: Case IH 433, 533, 633, 733, 833, 440, 540, 640, 740, 840, 940, 644, 744, 844, 844 S, 485XL, 585XL, 685XL, 743XL, 745XL, 785XL, 844XL, 845XL... More
To fit as: Case IH 433, 533, 633, 733, 833, 440, 540, 640, 740, 840, 9...
€23,68 €19,57
MANN-FILTER Fuel filter WK842
€18,79 €15,53
Knott Industrietechnik Brake shoe 254 x 70 mm Deutz-Fahr, Case IH
€356,32 €294,48 €327,81 €270,92
You save 8%
Spring clip for brake shoe hand brake Deutz-Fahr
€55,87 €46,17 €51,40 €42,48
You save 8%
Brake drum inner-Ø 250 mm, old version, with circlip Deutz-Fahr
€203,28 €168,00 €187,02 €154,56
You save 8%
Brake shoe Foot brake 254 x 70 mm Case IH, Deutz-Fahr
€102,72 €84,89 €94,50 €78,10
You save 8%
Showing 145 - 192 of 214

Deutz D 7007 parts for a classic that still works for a living

On plenty of farms a D 7007 from the 07 series still pulls the trailer or the muck spreader. To keep it that way there are more than 200 parts for this model, from GRANIT, LUK, HELLA, Bosch/Rexroth and VICTOR REINZ.

Brakes, steering and clutch

For the brakes you will find brake shoes and the matching return springs. Always fit new springs with new shoes. A spring that has been heat cycled for years loses tension and lets the shoe drag lightly on the drum, which shows up as a warm drum after a run on the road.

On the steering side there are ball joints and a bolt set for the steering valve. If the steering has play, have someone rock the wheel back and forth while you feel each joint by hand. That quickly tells you which one is worn. Use a fresh split pin every time you refit a joint.

For the clutch there are clutch plates and thrust bearings, including a sealed release bearing for the main clutch.

Engine and fuel system

Around the Deutz engine there are crankshaft seals, sealing rings and shims. On the exhaust side you will find exhaust manifolds and gaskets. Old manifold studs and nuts often come off with half the rust attached, so use new fixings and a new gasket, or the joint will be blowing again within weeks.

In the fuel system, a repair set for the feed pump helps when the engine is slow to fire or needs lengthy bleeding after standing. A lockable tank cap with a vent is also available.

For the electrics there are starter motors and alternators. A sluggish starter is not always at fault itself, so check the battery terminals and the earth connection first.

Working out what you need

On a tractor of this age, something has usually been replaced along the way. That makes it worth laying the old part next to the new one. A number stamped into or printed on the part is the quickest point of comparison. The tractor type plate gives the model and chassis number, which help when you are choosing between two versions of a clutch plate or starter.

These Deutz tractors from the same 07 series have their own pages too:

Useful when there is more than one classic in the yard. Newer and other models are under Deutz-Fahr parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison
This product has been added to your cart