Menu
EUR

Deutz-Fahr DX 120 tractor parts & technical data

More than 250 parts for the Deutz-Fahr DX 120 on a single page. Browse trailer couplings, electrics and lighting picked for this tractor from the DX series.

275 parts found for Deutz-Fahr DX 120
Show:
Alternator 14 V / 65 A, form B, flange 56,0 mm, pulley-Ø 68,0 mm
To fit as: Case IH, Claas, Deutz-Fahr, Fendt, Mercedes-Benz, Steyr, Zetor More
To fit as: Case IH, Claas, Deutz-Fahr, Fendt, Mercedes-Benz, Steyr, Ze...
€183,88 €151,97 €169,17 €139,81
You save 8%
Mirror black unheated 310 x 220 mm, rod Ø 16 - 18 mm
Tractor types: Deutz DX 80, 85, 86, 90, 92, 110, 120, 140, 145, 160, 230, 250, 3.10, 3.30, 3.50, 3.60, 3.65, 3.70, 3.80, 3.90, 4.10, 4.30, 4.50, 4.70,... More
Tractor types: Deutz DX 80, 85, 86, 90, 92, 110, 120, 140, 145, 160, 2...
€48,96 €40,46
Cylinder head with valves Deutz-Fahr
Engine types: FL912, FL913. Menke no.: 70536. More
Engine types: FL912, FL913. Menke no.: 70536.
€288,40 €238,35 €265,33 €219,28
You save 8%
Clutch kit double clutch Deutz-Fahr AgroPrima, AgroXtra, DX
Contents: Double clutch, clutch plate and 2x release bearing More
Contents: Double clutch, clutch plate and 2x release bearing
€1.138,27 €940,72 €1.097,21 €906,79
You save 4%
Replacement key lock number 14610 - 2 pieces
Locking number: 14610. Version: Locking no. 14610. More
Locking number: 14610. Version: Locking no. 14610.
€15,70 €12,98
Walterscheid Top drawbar rail 309 mm, pin Ø 22 mm, coupling pin 31 mm
Walterscheid
Rail width: 309 mm. Detent pin Ø: 22 mm. Guide width: 30 mm. Connecting pin: 31 mm. Load capacity: 2000 kg. D-value: 92 kN. Colour: Black. Descriptio... More
Rail width: 309 mm. Detent pin Ø: 22 mm. Guide width: 30 mm. Connecti...
€1.104,81 €913,07 €873,47 €721,88
You save 21%
Alternator 14 V / 33 A, form B, flange 56,0 mm, pulley-Ø 68,0 mm
To fit as: Antonio Carraro, Case IH, Deutz-Fahr, Fendt, Goldoni, Holder, Renault, Schlüter More
To fit as: Antonio Carraro, Case IH, Deutz-Fahr, Fendt, Goldoni, Holde...
€197,74 €163,42 €181,92 €150,35
You save 8%
ROCKINGER Trailer coupling hitch pin 30,6 mm, rail 330 mm, 2000 kg, black
ROCKINGER
Rail width (mm): 330 | Guide width (mm): 32 | Drawbar eye: DIN 11026 40 mm, DIN 11043 40 mm, DIN 74054 40 mm | D-value (kN): 120,0 | Type: RO 850 D | ... More
Rail width (mm): 330 | Guide width (mm): 32 | Drawbar eye: DIN 11026 4...
€1.126,27 €930,80 €917,77 €758,49
You save 19%
Steering valve ew/dw 220 bar, 60 l/min, system SD60 Deutz
This control valve has been specially developed for Deutz tractors with SD60 hydraulics. Thanks to the high output up to four pieces can be flanged di... More
This control valve has been specially developed for Deutz tractors wit...
€663,73 €548,54 €610,63 €504,65
You save 8%
Walterscheid Inner part ball 80 rail width 309 mm, pin Ø 22 mm, 3000 kg
Walterscheid
D-value (kN): 89.3 | Colour: Black | Assembly notes: Suitable for connection to ball hitches 80 according to ISO 24347. The 80 mm diameter ball can be... More
D-value (kN): 89.3 | Colour: Black | Assembly notes: Suitable for conn...
€2.146,48 €1.773,95 €1.697,03 €1.402,50
You save 21%
LUK Thrust bearing PTO clutch 75 x 115 x 20 mm
LUK
Dimensions (mm): 75 x 115 x 20 More
Dimensions (mm): 75 x 115 x 20
€183,54 €151,69 €168,86 €139,55
You save 8%
Alternator 14 V / 95 A, flange 56 mm
Mounting L / d / R (mm): 56,0 / 8,3 / 86,0 | Pulley spacing (mm): - | Pulley Ø (mm): - | Form: B | Flange size (mm): 56,0 | Nominal values (V / A): 1... More
Mounting L / d / R (mm): 56,0 / 8,3 / 86,0 | Pulley spacing (mm): - | ...
€193,94 €160,28 €178,42 €147,46
You save 8%
HELLA Alternator 14 V, 33 A Case IH, Deutz-Fahr, John Deere
HELLA
Nominal values (V / A): 14 / 33 | Charging current (A): 33 | Nominal voltage (V): 14 | Additional information: Without pulley More
Nominal values (V / A): 14 / 33 | Charging current (A): 33 | Nominal v...
€354,91 €293,31 €273,45 €225,99
You save 23%
Gear reduction starter 12 V, 4,0 kW, 9 teeth, 245 mm, clockwise
€299,69 €247,68 €275,71 €227,86
You save 8%
Hydraulic cylinder Deutz-Fahr DX 6.05-250, Series DX 6-7
€1.361,03 €1.124,82 €1.252,15 €1.034,83
You save 8%
HELLA Flasher unit 12 V, 2+1+1 / 8 x 21 W, 6 connections, with cable
HELLA
Version: Power rating: 12 V / 2 + 1 + 1 x 21 W / 8 x 21 W, With hazard warning light function, with cable and bracket. Additional information: • Rel... More
Version: Power rating: 12 V / 2 + 1 + 1 x 21 W / 8 x 21 W, With hazard...
€80,43 €66,47 €77,45 €64,01
You save 4%
Drive shaft 1050 mm Deutz-Fahr DX 80 - 120, DX 4.10 - 6.05
€992,43 €820,19 €913,04 €754,57
You save 8%
LUK Thrust bearing 55 x 90,5 x 22 mm
LUK
Dimensions (mm): 55 x 90.5 x 22 More
Dimensions (mm): 55 x 90.5 x 22
€192,19 €158,83 €176,81 €146,13
You save 8%
GRAMMER Tractor seat Maximo Comfort Plus air suspended, 530 mm, Deutz VII
GRAMMER
Seat heater: Optional | Length (mm): 631 | Included in delivery: Seat supplied with seat contact switch and bracket for your existing control armrest.... More
Seat heater: Optional | Length (mm): 631 | Included in delivery: Seat ...
€2.132,30 €1.762,23
Bolt set 2de steering valve 3x M8 x 180
Technical data: 3x M8 x 180. Menke no.: 51682. Description: For 3rd Control unit. More
Technical data: 3x M8 x 180. Menke no.: 51682. Description: For 3rd Co...
€29,14 €24,08
Walterscheid Trailer coupling hitch pin 38 mm, 65,6 kN, black Deutz-Fahr
Walterscheid
Colour: Black | Load capacity (kg): 2000 | Lock: Automatic, spherical hitch bolt | Included in delivery: Includes 1x coupling 770KU2000/758NB. Locking... More
Colour: Black | Load capacity (kg): 2000 | Lock: Automatic, spherical ...
€2.242,44 €1.853,26 €1.772,89 €1.465,20
You save 21%
LUK Clutch kit double clutch Ø 310 mm Deutz-Fahr
LUK
Disc Ø (mm): 310 | Contents: Double clutch and clutch plate More
Disc Ø (mm): 310 | Contents: Double clutch and clutch plate
€1.123,75 €928,72 €1.083,85 €895,74
You save 4%
Alternator 14 V / 35 A, flange 56 mm, pulley Ø 68 mm, W-connection
Additional information: with W connection | Mounting L / d / R (mm): 56,0 / 8,3 / 86,0 | Installation angle (°): l 60 | Charging current (A): 35 | Fo... More
Additional information: with W connection | Mounting L / d / R (mm): 5...
€122,13 €100,93 €112,36 €92,86
You save 8%
AKS-Dasis Blower switch 3 link steps Deutz-Fahr DX 4.10 - DX 120
AKS-Dasis
Equipment: 3 switching stages More
Equipment: 3 switching stages
€43,95 €36,32 €40,43 €33,42
You save 8%
Expansion valve airco 1/2 inch o-ring, 35 g
Weight (g): 35 | Equipment: O-ring | Connection thread A: # 8, 1/2"" O-ring | Connection thread E: - More
Weight (g): 35 | Equipment: O-ring | Connection thread A: # 8, 1/2"" O...
€54,07 €44,69 €49,74 €41,11
You save 8%
Rivet copper 5 x 10 mm, DIN 7338-B - 100 pieces
Hole Ø: 5 mm. Length: 10 mm. d2: 9,5 mm. K: 1 mm. e: 2,5 mm. Material: Copper. DIN: 7338-B. More
Hole Ø: 5 mm. Length: 10 mm. d2: 9,5 mm. K: 1 mm. e: 2,5 mm. Material...
€50,38 €41,64 €46,35 €38,31
You save 8%
ROCKINGER Adapter plate rail width 330 mm, 93,6 kN, 2500 kg, 160 x 100 mm
ROCKINGER
Colour: Black | Hole pattern (mm): 160 x 100 | Guide width (mm): 32 | Detent pin Ø (mm): 25 | D-value (kN): 93,6 | Load capacity (kg): 2500 | Rail wi... More
Colour: Black | Hole pattern (mm): 160 x 100 | Guide width (mm): 32 | ...
€651,63 €538,54 €627,60 €518,67
You save 4%
Bosch/Rexroth Hydraulic pump 22,5 cm³ left Deutz-Fahr DX 85 - 145
Bosch/Rexroth
Drive shaft: Splined shaft 17 x 14 9 splines | Adaptor plate hole pattern (mm): 60 x 60 (2 x) | Operating pressure max. (bar): 220 | Bosch no.: 151722... More
Drive shaft: Splined shaft 17 x 14 9 splines | Adaptor plate hole patt...
€653,73 €540,27 €601,43 €497,05
You save 8%
Scharmüller Drawbar frame 43,2 kN, rail 330 mm, guide 32 mm, pin Ø 25 mm
Scharmüller
Detent pin Ø (mm): 25 | Category: Bearing supports | Load capacity (kg): 2000 | Guide width (mm): 32 | Rail width (mm): 330 | Version: Prepared for d... More
Detent pin Ø (mm): 25 | Category: Bearing supports | Load capacity (k...
€1.074,22 €887,79 €1.038,28 €858,08
You save 3%
MAHLE Alternator 14 V, 95 A, fastening 56 / 8,2 / 86 mm
MAHLE
Nominal voltage (V): 14 | Direction of rotation: ↻ | Additional information: Dust-tight, with fan | Mounting L / d / R (mm): 56,0 / 8,2 / 86,0 | Cha... More
Nominal voltage (V): 14 | Direction of rotation: ↻ | Additional info...
€334,90 €276,78 €200,59 €165,78
You save 40%
Elring Cylinder head gasket set without cylinder head gasket engine FL912, FL913, BFL913
Elring
Supplementary set: For one cylinder head | Additional information: Without cylinder head gasket More
Supplementary set: For one cylinder head | Additional information: Wit...
€34,58 €28,57
MAHLE Starter motor 12 V, 3,1 kW, 9 teeth, 232 mm, clockwise
€662,73 €547,71 €396,94 €328,05
You save 40%
Seal tank cap Deutz-Fahr
Angle drive transmission 1:1, 1x M18 x 1,5, 1x M22 x 1,5
Version: VDO 33/83/1, Thread: 1 x M18 x 1.5, 1 x M22 x 1.5. More
Version: VDO 33/83/1, Thread: 1 x M18 x 1.5, 1 x M22 x 1.5.
€163,89 €135,45 €150,78 €124,61
You save 8%
Walterscheid Ball hitch ball 80, rail width 309 mm, pin Ø 22 mm, 2800 kg
Walterscheid
Description: This product is a ball hitch. The hitch ball 80 dimensions and areas of application comply with ISO 24347, VO (EU) 2015/208 and UN ECE R1... More
Description: This product is a ball hitch. The hitch ball 80 dimension...
€2.071,98 €1.712,38 €1.638,13 €1.353,83
You save 21%
LUK Double clutch 310/310TGU 41 x 45 mm, 21 splines sintered Deutz-Fahr
LUK
Material specifications: Sintered clutch lining | Dimensions (mm): 41 x 45, 21 grooves More
Material specifications: Sintered clutch lining | Dimensions (mm): 41 ...
€1.194,07 €986,83 €1.148,54 €949,21
You save 4%
Filter dryer airco 229 mm, Ø 76 mm, #6 3/8 o-ring Deutz-Fahr, Fendt
Material: Steel | Thread: #6 3/8 O-ring | Weight (g): 783 | Connection thread E: 3/8"" | Connection thread A: 3/8"" | Connection thread: 10 | Outer Ø... More
Material: Steel | Thread: #6 3/8 O-ring | Weight (g): 783 | Connection...
€60,62 €50,10 €55,77 €46,09
You save 8%
LUK Thrust bearing PTO shaft 70 x 110 x 20 mm
LUK
Dimensions (mm): 70 x 110 x 20 More
Dimensions (mm): 70 x 110 x 20
€116,29 €96,11 €106,99 €88,42
You save 8%
HELLA Alternator CA1433IR 14 V / 95 A without belt pulley
HELLA
Charging current (A): 95 | Nominal voltage (V): 14 | Additional information: Without pulley | Nominal values (V / A): 14 / 95 More
Charging current (A): 95 | Nominal voltage (V): 14 | Additional inform...
€503,99 €416,52 €388,33 €320,93
You save 23%
Thrust bearing driving clutch 55 x 91,5 x 25 mm
Dimensions (mm): 55 x 91.5 x 25 More
Dimensions (mm): 55 x 91.5 x 25
€87,90 €72,64 €80,87 €66,83
You save 8%
Pilot bearing 20 x 52 x 15 mm Deutz-Fahr, Lamborghini
Dimensions (mm): 20 x 52 x 15 More
Dimensions (mm): 20 x 52 x 15
€11,65 €9,63
Track rod 1160 mm, taper 20 - 22 mm Deutz-Fahr
C (mm): 20 - 22 | A (mm): 1160 | G (mm): 20 - 22 More
C (mm): 20 - 22 | A (mm): 1160 | G (mm): 20 - 22
€781,56 €645,92 €719,04 €594,24
You save 8%
Wiper motor without integrated switch 12 V, 135°, M12 x 1
Volts: 12. W: konisch 8 x M6 mm. Angle: 135 °. A: 53 mm. B: 34 mm. C: 28 mm. D: M12 x 1 mm. E: 6 mm. F: M8 mm. G: 50-57 mm. Wiper blade length max.: ... More
Volts: 12. W: konisch 8 x M6 mm. Angle: 135 °. A: 53 mm. B: 34 mm. C:...
€145,99 €120,65 €134,31 €111,00
You save 8%
Stabilus Gas strut door-, for- or rear window 230 N, 502 mm, stroke 198 mm
Stabilus
To fit as: Deutz Door, windscreen or rear screen More
To fit as: Deutz Door, windscreen or rear screen
€47,75 €39,46 €43,93 €36,31
You save 8%
AKS-Dasis Air conditioning compressor 12 V, pulley Ø 152 mm, 175 ccm oil Deutz-Fahr
AKS-Dasis
Oil quantity (ccm): 175 | Pulley Ø (mm): 152 | Nominal voltage (V): 12 | Additional information: Cylinder head ID: B Inlet: 19.1 mm Outlet: 22.2 mm |... More
Oil quantity (ccm): 175 | Pulley Ø (mm): 152 | Nominal voltage (V): 1...
€504,50 €416,94 €464,14 €383,59
You save 8%
Scharmüller Drawbar frame prepared for drawbar 270 mm, 43,2 kN Kubota M5N
Scharmüller
D-value (kN): 43,2 | Version: Prepared for drawbar | Colour: Kubota grey | Guide width (mm): 32 | Load capacity (kg): 1500 | Category: Bearing support... More
D-value (kN): 43,2 | Version: Prepared for drawbar | Colour: Kubota gr...
€1.378,56 €1.139,31 €1.318,28 €1.089,49
You save 4%
Scharmüller Drawbar frame 74 kN, 3000 kg, rail 330 mm, pin Ø 25 mm, draw pendulum
Scharmüller
D-value (kN): 74 | Version: Prepared for drawbar | Rail width (mm): 330 | Detent pin Ø (mm): 25 | Load capacity (kg): 3000 | Colour: Kubota grey | Gu... More
D-value (kN): 74 | Version: Prepared for drawbar | Rail width (mm): 33...
€1.288,81 €1.065,13 €1.235,71 €1.021,25
You save 4%
Showing 1 - 48 of 275

Deutz-Fahr DX 120 parts for the clutch, engine and cab

Sooner or later a DX 120 that has worked for decades needs proper attention. The tractor gets split for a new clutch, or the head comes off because compression is dropping. For the Deutz-Fahr DX 120 there are more than 250 parts on this page, and a good share of them belong to exactly those jobs.

Splitting the tractor for the clutch

For the clutch there are clutch kits and thrust bearings for the driving clutch. Once the tractor is apart, replace the thrust bearing and the rear crankshaft seal at the same time. You cannot reach either of them otherwise, and a weeping seal soaks the new clutch plate in oil. That puts you back to splitting the tractor within a season, which is a job nobody wants to do twice.

Engine and electrics

For engine work you will find piston ring sets, crankshaft seals and repair kits, for example for the feed pump. When the electrics give up there are alternators and starter motors as well. A starter that clicks but does not turn is often down to a poor earth or a tired battery, so check those first before you swap it.

Around the rest of the tractor

  • Sealing rings, including ones for the lift shaft
  • Bolt sets, for example for the steering valve
  • Gas struts for the door, front screen or rear window
  • Push button switches, such as the one for the work lamp
  • Tank caps
  • Drawbars and drawbar frames

The parts come from GRANIT, LUK, HELLA, ROCKINGER and Walterscheid.

Getting the right part for a DX 120

The DX family has many types that look alike from the outside, so read the type plate before you order anything. For engine parts like seals and piston rings, the reference number on the old part is the surest guide. If it has worn off, measure the old part and compare it with the details given for the product. A seal that is slightly off will start leaking again in no time. With gas struts the mounting position matters, because the door strut differs from the one for the rear window. Replace them in pairs so the window stays level when open.

Running another Deutz-Fahr next to the DX 120, an Agrotron or an older DX perhaps? Every type from the brand is on Deutz-Fahr parts, where you pick the model and see what fits it.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison
This product has been added to your cart