Menu
EUR

Deutz-Fahr DX 120 tractor parts & technical data

More than 250 parts for the Deutz-Fahr DX 120 on a single page. Browse trailer couplings, electrics and lighting picked for this tractor from the DX series.

275 parts found for Deutz-Fahr DX 120
Show:
MAHLE Alternator 14 V / 65 A, flange 56 mm, form B Deutz-Fahr, Fendt, Steyr
MAHLE
Nominal values (V / A): 14 / 65 | Direction of rotation: ↻ | Additional information: Dust-tight | Installation angle (°): l 60 | Mounting L / d / R... More
Nominal values (V / A): 14 / 65 | Direction of rotation: ↻ | Additio...
€326,57 €269,89 €195,60 €161,65
You save 40%
Filter dryer airco Ø 102 mm, 190 mm, F/M #6 O-ring, steel
Length (mm): 190 | Outer Ø (mm): 102 | Connection thread: F/M #6 O-ring | Dimensions (mm): - | Material: Steel More
Length (mm): 190 | Outer Ø (mm): 102 | Connection thread: F/M #6 O-ri...
€65,38 €54,03 €60,15 €49,71
You save 8%
GRAMMER Tractor seat Maximo Comfort Plus air suspended, 530 mm, Deutz VI
GRAMMER
Joystick console: Yes | Seat width (mm): 530 | Height (mm): 754 | Restraint system: Optional | - Super comfort seat with air suspension and 12V compre... More
Joystick console: Yes | Seat width (mm): 530 | Height (mm): 754 | Rest...
€2.293,87 €1.895,76
FEBI Fuel filter WK842
€19,60 €16,20 €8,47 €7,00
You save 57%
BOSCH Gear reduction starter 12 V, 3,0 kW, 9 teeth, Ø 89 mm, flange 31 mm
€512,28 €423,37 €493,38 €407,75
You save 4%
BOSCH Starter motor 12 V, 2,7 kW, 9 teeth, mounting Ø 89 mm, clockwise
€569,55 €470,70 €548,54 €453,34
You save 4%
Master brake cylinder piston Ø 19,05 mm, DOT 4 Deutz-Fahr
€483,27 €399,40 €444,61 €367,45
You save 8%
Repair set feed pump set of parts outer-Ø 41 mm Deutz-Fahr, Linde
€20,01 €16,54
Bearing bush camshaft 47,9 x 52 x 30,5 mm Fendt, Deutz-Fahr
Dimensions: Inner Ø 47.9, outer Ø 52, width 30.5 mm. More
Dimensions: Inner Ø 47.9, outer Ø 52, width 30.5 mm.
€33,53 €27,71
O-ring feed pump Ø 38 x 3 mm Deutz engine 912, 913W/T
Version: Ø 38 x 3 mm. More
Version: Ø 38 x 3 mm.
€7,99 €6,60
HELLA Interior light K (10W), clear, 12 / 24 V, built-in
HELLA
Bulb: K (10W). Colour: Transparent. Installation location: Inner. Nominal voltage: 12 / 24 V. Switches: Yes. Test mark: E1 8728, ECE. Type: Bulb. Ligh... More
Bulb: K (10W). Colour: Transparent. Installation location: Inner. Nomi...
€15,94 €13,17
Wiper motor with switch 12 V, 135°, M12 x 1
With integrated switch. More
With integrated switch.
€127,48 €105,36 €117,28 €96,93
You save 8%
Drive shaft 1445 mm Deutz-Fahr DX 85 - DX 120
€801,46 €662,36 €737,34 €609,37
You save 8%
LUK Clutch kit Ø 280 mm Deutz-Fahr AgroPrima 4.31 - 6.16, DX 4.10 - 120
LUK
Contents: Pressure plate 458231002017, clutch plate 458328011616 More
Contents: Pressure plate 458231002017, clutch plate 458328011616
€1.199,68 €991,47 €1.153,71 €953,48
You save 4%
Scharmüller Clutch complete type 1120 coupling pin 38 mm, nose weight 1250 kg
Scharmüller
Hole (mm): M20 | Overhang (mm): 211 | Thread: M20 | Lock: Automatic | Internal width (mm): 98 | Colour: Black | Hole spacing (mm): 129 | D-value (kN):... More
Hole (mm): M20 | Overhang (mm): 211 | Thread: M20 | Lock: Automatic | ...
€1.364,15 €1.127,40 €1.261,52 €1.042,58
You save 8%
SACHS Thrust bearing 55 x 91 x 22 mm Deutz-Fahr D 6006-D 7807, DX 80-DX 120
SACHS
Dimensions (mm): 55 x 91 x 22 More
Dimensions (mm): 55 x 91 x 22
€215,70 €178,26 €198,44 €164,00
You save 8%
LUK Pilot bearing 20 x 52 x 15 mm Deutz-Fahr, Fendt, Lamborghini, Steyr
LUK
Dimensions (mm): 20 x 52 x 15 More
Dimensions (mm): 20 x 52 x 15
€35,51 €29,35 €32,67 €27,00
You save 8%
LUK Clutch plate 280UKF 31 x 36 mm, 16 splines Deutz-Fahr
LUK
Dimensions (mm): 31 x 36 16 grooves More
Dimensions (mm): 31 x 36 16 grooves
€215,77 €178,32 €198,51 €164,06
You save 8%
Clutch plate 310, 31 x 36 mm, 16 splines Deutz-Fahr
Additional information: Made in Germany | Dimensions (mm): 31 x 36, 16 grooves More
Additional information: Made in Germany | Dimensions (mm): 31 x 36, 16...
€199,10 €164,55 €183,17 €151,38
You save 8%
Thrust bearing single PTO clutch 70 x 110 x 20 mm
Dimensions (mm): 70 x 110 x 20 More
Dimensions (mm): 70 x 110 x 20
€36,11 €29,84 €33,22 €27,46
You save 8%
Elring Cylinder head bolt set M12 x 1,75 x 211 mm, wrench size 17 - 4 pieces
Elring
Notes: Set of 4 | Dimensions (mm): M12 x 1.75 x 211 | Supplementary set: For one cylinder head | AF (mm): 17 More
Notes: Set of 4 | Dimensions (mm): M12 x 1.75 x 211 | Supplementary se...
€118,56 €97,98 €109,08 €90,14
You save 8%
Starter motor with reduction 12 V, 2,7 kW, 9 teeth, 208,5 mm
€541,43 €447,46 €498,12 €411,67
You save 8%
Starter ring gear Ø 393/364 mm, 129 teeth Deutz
Version: Ø 393/364 mm, 129 teeth. More
Version: Ø 393/364 mm, 129 teeth.
€82,99 €68,59 €76,35 €63,10
You save 8%
Exhaust manifold Deutz-Fahr DX 85-120, DX 6.10-6.30
€351,29 €290,32 €323,19 €267,10
You save 8%
Rocker arm shaft engine FL912, FL913, FL712, FL812 Fendt, Deutz-Fahr
Engine types: FL912, FL913, FL712, FL812. More
Engine types: FL912, FL913, FL712, FL812.
€15,21 €12,57
HELLA Indicator/position light 120 x 80 x 55 mm, P21W, R5W left / right
HELLA
Bulb: 12V21WK / P21W, 12V5WK / R5W. Colour: Yellow, white. Attachment: Front. Connection: Blade terminal. Width: 120 mm. Form: Rectangular. Height: 80... More
Bulb: 12V21WK / P21W, 12V5WK / R5W. Colour: Yellow, white. Attachment:...
€28,18 €23,29
Silencer vertical 1230 mm, Ø 67 mm, exhaust Ø 70 mm Deutz-Fahr
To fit as: Deutz DX 85, 90, 110, 120, DX 6.10, 6.30 More
To fit as: Deutz DX 85, 90, 110, 120, DX 6.10, 6.30
€268,88 €222,21 €247,37 €204,44
You save 8%
LUK Clutch plate 310UKF 31 x 35 mm 16 splines Deutz-Fahr
LUK
Dimensions (mm): 31 x 35 16 grooves More
Dimensions (mm): 31 x 35 16 grooves
€250,68 €207,17 €230,63 €190,60
You save 8%
Elring Crankshaft seal rear 115 x 140 x 13 mm, FPM, engine FL912 - BFL913
Elring
Width (mm): 13 | Inner Ø (mm): 115 | Outer Ø (mm): 140 | Material: FPM (fluoro rubber) More
Width (mm): 13 | Inner Ø (mm): 115 | Outer Ø (mm): 140 | Material: F...
€70,51 €58,27 €64,87 €53,61
You save 8%
Push rod brake cylinder DOT4 Deutz-Fahr
€36,41 €30,09 €33,50 €27,68
You save 8%
Optibelt V-belt engine cooling Deutz-Fahr DX 85-120, D 8006-10006
€36,87 €30,47 €33,92 €28,03
You save 8%
Feed pump in-line pump 3 bores, hole spacing 52/34 mm, flange 26 mm
Version: 3 holes, Vertical hole spacing: 52 mm, Horizontal hole spacing: 34 mm, Flange to lever end: 26 mm. Menke no.: 45815. More
Version: 3 holes, Vertical hole spacing: 52 mm, Horizontal hole spacin...
€36,59 €30,24
Piston ring set 3 rings Ø 102 mm, 2,94 mm trapezoidal ring / 3 mm / 3 mm
Dimensions: 3 rings, Ø 102 mm, 2.94 mm (trapezoidal ring) / 3 mm / 3 mm. More
Dimensions: 3 rings, Ø 102 mm, 2.94 mm (trapezoidal ring) / 3 mm / 3 ...
€104,55 €86,41 €96,19 €79,49
You save 8%
Piston ring set 3 rings Ø 102 mm, 2x 3 mm trapezoidal ring / 3,5 mm
Dimensions: 3 rings, Ø 102 mm, 3 mm (trapezoidal ring) / 3 mm (trapezoidal ring) / 3.5 mm. More
Dimensions: 3 rings, Ø 102 mm, 3 mm (trapezoidal ring) / 3 mm (trapez...
€59,80 €49,42 €55,02 €45,47
You save 8%
Sealing ring push rod tube Fendt, Deutz-Fahr
Engine types: FL712, FL812. More
Engine types: FL712, FL812.
€1,73 €1,43
Manifold gasket exhaust Fendt, Deutz-Fahr
Engine types: FL712, FL812. More
Engine types: FL712, FL812.
€4,89 €4,04
Bolt set 1ste steering valve 3x M8 x 90
Technical data: 3x M8 x 90. More
Technical data: 3x M8 x 90.
€18,40 €15,21
ROCKINGER Piton Fix rail width 330 mm, locking pin Ø 25 mm, 3000 kg, 102 kN
ROCKINGER
Rail width: 330 mm. Detent pin Ø: 25 mm. Guide width: 32 mm. Load capacity: 3000 kg. D-value: 102 kN. Description: Piton-Fix with manual lock and hei... More
Rail width: 330 mm. Detent pin Ø: 25 mm. Guide width: 32 mm. Load cap...
€1.504,05 €1.243,02 €1.158,85 €957,72
You save 23%
ROCKINGER Drawbar inner part 310 mm, coupling pin 31,5 mm, 2000 kg
ROCKINGER
Rail width: 310 mm. Detent pin Ø: 22 mm. Guide width: 30 mm. Connecting pin: 31,5 mm. Load capacity: 2000 kg. D-value: 97,1 kN. Colour: Black. Drawba... More
Rail width: 310 mm. Detent pin Ø: 22 mm. Guide width: 30 mm. Connecti...
€910,37 €752,37 €876,79 €724,62
You save 4%
Push button switch hazard lights 12 / 24 V red, with lock
Version: 12/24 V, Red button, with lock, Ø 30 mm, 7 blade terminals 6.3 x 0.8 (L- R- 30- 30b- 49a- 15- 49), dustproof and splashproof, With glass soc... More
Version: 12/24 V, Red button, with lock, Ø 30 mm, 7 blade terminals 6...
€57,83 €47,79 €53,20 €43,97
You save 8%
Rotary switch ventilation, without knob, 5 connections
Version: For blower, 3 switching steps, With 5 blade terminals. More
Version: For blower, 3 switching steps, With 5 blade terminals.
€42,59 €35,20 €39,18 €32,38
You save 8%
Flasher unit 12 V, 2+1+1 x 21 W, with holder and indicator instruments
To fit as: Case IH 238, 248, 258, 268, 278, 288, 323, 354, 374, 384, 444, 474, 475, 484, 584, 674, 684, 784, 884 385, 485, 485XL, 585, 585XL, 685, 685... More
To fit as: Case IH 238, 248, 258, 268, 278, 288, 323, 354, 374, 384, 4...
€48,67 €40,22 €44,78 €37,01
You save 8%
Showing 49 - 96 of 275

Deutz-Fahr DX 120 parts for the clutch, engine and cab

Sooner or later a DX 120 that has worked for decades needs proper attention. The tractor gets split for a new clutch, or the head comes off because compression is dropping. For the Deutz-Fahr DX 120 there are more than 250 parts on this page, and a good share of them belong to exactly those jobs.

Splitting the tractor for the clutch

For the clutch there are clutch kits and thrust bearings for the driving clutch. Once the tractor is apart, replace the thrust bearing and the rear crankshaft seal at the same time. You cannot reach either of them otherwise, and a weeping seal soaks the new clutch plate in oil. That puts you back to splitting the tractor within a season, which is a job nobody wants to do twice.

Engine and electrics

For engine work you will find piston ring sets, crankshaft seals and repair kits, for example for the feed pump. When the electrics give up there are alternators and starter motors as well. A starter that clicks but does not turn is often down to a poor earth or a tired battery, so check those first before you swap it.

Around the rest of the tractor

  • Sealing rings, including ones for the lift shaft
  • Bolt sets, for example for the steering valve
  • Gas struts for the door, front screen or rear window
  • Push button switches, such as the one for the work lamp
  • Tank caps
  • Drawbars and drawbar frames

The parts come from GRANIT, LUK, HELLA, ROCKINGER and Walterscheid.

Getting the right part for a DX 120

The DX family has many types that look alike from the outside, so read the type plate before you order anything. For engine parts like seals and piston rings, the reference number on the old part is the surest guide. If it has worn off, measure the old part and compare it with the details given for the product. A seal that is slightly off will start leaking again in no time. With gas struts the mounting position matters, because the door strut differs from the one for the rear window. Replace them in pairs so the window stays level when open.

Running another Deutz-Fahr next to the DX 120, an Agrotron or an older DX perhaps? Every type from the brand is on Deutz-Fahr parts, where you pick the model and see what fits it.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison
This product has been added to your cart