Menu
EUR

Deutz D 7007 tractor parts & technical data

If the lights on your Deutz D 7007 have failed or the electrics are playing up, this page lists more than 200 parts that fit this 07 series tractor.

213 parts found for Deutz-Fahr D 7007
Show:
VICTOR REINZ Crankshaft seal for Ø 65 x 85 x 10,5 mm engine FL912, FL913 Deutz-Fahr
5%
VICTOR REINZ
Crankshaft seal for Ø 65 x 85 x 10,5 mm engine FL912, FL913 Deutz-Fahr
€35,82 €29,60 €34,00 €28,10
 
VICTOR REINZ Cylinder head gasket 1,1 mm, outer-Ø 120 mm Fendt, Deutz-Fahr
VICTOR REINZ
Cylinder head gasket 1,1 mm, outer-Ø 120 mm Fendt, Deutz-Fahr
Engine types: FL912, FL913, BFL912, BFL913. Colour: A-Form. Outer Ø: 120 mm. Inn...
€10,25 €8,47
 
Cooling fan Ø 230 mm Fendt, Deutz-Fahr
5%
Cooling fan Ø 230 mm Fendt, Deutz-Fahr
Ø: 230 mm.
€256,36 €211,87 €243,50 €201,24
 
GRANIT Bush for fan Deutz-Fahr
GRANIT
Bush for fan Deutz-Fahr
€79,25 €65,50
 
Flame glow plug 9,5 V, 20 A, M20 x 1,5 Deutz, SAME, Deutz-Fahr
5%
Flame glow plug 9,5 V, 20 A, M20 x 1,5 Deutz, SAME, Deutz-Fahr
Version: 9.5 V, 20 A, thread M20 x 1.5. To fit: Deutz.
€75,35 €62,27 €71,55 €59,13
 
Piston ring set 4 rings, Ø 100 mm Fendt, Deutz-Fahr
5%
Piston ring set 4 rings, Ø 100 mm Fendt, Deutz-Fahr
Dimensions: 4 rings, Ø 100 mm, 3 mm (trapezoidal ring) / 2.5 mm / 2.5 mm / 5 mm.
€41,90 €34,63 €39,80 €32,89
 
Thermag nut exhaust manifold M8, height 8,5 mm Deutz FL712, FL812
Thermag nut exhaust manifold M8, height 8,5 mm Deutz FL712, FL812
Engine types: FL712, FL812. Thread: M8. Version: Thread M8, Height: 8.5 mm.
€1,21 €1,00
 
Return line Fendt, Deutz-Fahr
5%
Return line Fendt, Deutz-Fahr
€171,47 €141,71 €162,85 €134,59
 
Steering valve dw not blocked 210 bar, 70 l/min, system SD60
5%
Steering valve dw not blocked 210 bar, 70 l/min, system SD60
Technical data: Max. operating pressure: 210 bar, Nominal flow rate: max. 70 l/m...
€636,06 €525,67 €604,25 €499,38
 
Seal kit flange face additional control unit SD60 Deutz-Fahr
Seal kit flange face additional control unit SD60 Deutz-Fahr
Menke no.: 51722.
€31,65 €26,16
 
Bosch/Rexroth Hydraulic pump 16 cm³/rpm., taper 1:5, Ø 17 x 17, left Fendt, Deutz-Fahr
5%
Bosch/Rexroth
Hydraulic pump 16 cm³/rpm., taper 1:5, Ø 17 x 17, left Fendt, Deutz-Fahr
Output volume: 16 cc/rev. Drive shaft: Taper 1:5, Ø 17 x 17. Operating pressure ...
€616,19 €509,25 €585,35 €483,76
 
Sealing ring piston 84 x 88 x 1,5 mm Deutz-Fahr
Sealing ring piston 84 x 88 x 1,5 mm Deutz-Fahr
Dimensions: 84 x 88 x 1.5 mm.
€33,20 €27,44
 
GRANIT Protective grille upper Deutz D 2807 - D 7807
5%
GRANIT
Protective grille upper Deutz D 2807 - D 7807
€216,59 €179,00 €205,75 €170,04
 
GRANIT Rivet copper 5 x 10 mm, DIN 7338-B - 100 pieces
5%
GRANIT
Rivet copper 5 x 10 mm, DIN 7338-B - 100 pieces
Hole Ø: 5 mm. Length: 10 mm. d2: 9,5 mm. K: 1 mm. e: 2,5 mm. Material: Copper. D...
€50,52 €41,75 €47,95 €39,63
 
Rivet copper 5 x 12 mm, DIN 7338-B - 100 pieces
10%
Rivet copper 5 x 12 mm, DIN 7338-B - 100 pieces
Hole Ø: 5 mm. Length: 12 mm. d2: 9,5 mm. K: 1 mm. e: 2,5 mm. Material: Copper. D...
€67,08 €55,44 €60,65 €50,12
 
Brake light switch mechanical M14 x 1, break contact, blade terminal 6,3 mm
Brake light switch mechanical M14 x 1, break contact, blade terminal 6,3 mm
Version: Thread M14 x 1, break contact, normally on, Blade terminals 6.3 mm. Men...
€35,35 €29,21
 
SACHS Clutch plate 280, 26 x 32 mm, 10 splines Deutz-Fahr
SACHS
Clutch plate 280, 26 x 32 mm, 10 splines Deutz-Fahr
Dimensions (mm): 26 x 32 10 grooves
€234,70 €193,97
 
LUK Double clutch 300 / 250TGA 36 x 42 mm, 8 splines, chain pitch 20 mm
10%
LUK
Double clutch 300 / 250TGA 36 x 42 mm, 8 splines, chain pitch 20 mm
Dimensions (mm): 36 x 42 8 grooves | web (mm): 20 | Flywheel dimension (mm): 36 ...
€1.049,43 €867,30 €949,45 €784,67
 
Bosch/Rexroth Hydraulic pump 16 cm³ anticlockwise, taper 1:5, Ø 17 x 17 Deutz-Fahr
5%
Bosch/Rexroth
Hydraulic pump 16 cm³ anticlockwise, taper 1:5, Ø 17 x 17 Deutz-Fahr
Bosch no.: 1517222359 | Direction of rotation: Anticlockwise | Output volume (cc...
€611,40 €505,29 €580,80 €480,00
 
Clutch plate 250, 26 x 32 mm, 10 splines Deutz-Fahr
5%
Clutch plate 250, 26 x 32 mm, 10 splines Deutz-Fahr
Dimensions (mm): 26 x 32, 10 grooves | Additional information: Made in Germany
€137,13 €113,33 €130,25 €107,64
 
GRANIT Thrust bearing driving clutch 55 x 91,5 x 25 mm
5%
GRANIT
Thrust bearing driving clutch 55 x 91,5 x 25 mm
Dimensions (mm): 55 x 91.5 x 25
€84,24 €69,62 €80,00 €66,12
 
HELLA Alternator 14 V, 33 A Case IH, Deutz-Fahr, John Deere
20%
HELLA
Alternator 14 V, 33 A Case IH, Deutz-Fahr, John Deere
Nominal values (V / A): 14 / 33 | Charging current (A): 33 | Nominal voltage (V)...
€340,12 €281,09 €273,40 €225,95
 
Track rod telescopic axle, hydraulic steering A 1230 - 1740 mm
5%
Track rod telescopic axle, hydraulic steering A 1230 - 1740 mm
A: 1230 - 1740 mm. C: 20 - 22 mm. G: .
€710,32 €587,04 €674,80 €557,69
 
Showing 97 - 120 of 213

Deutz D 7007 parts for a classic that still works for a living

On plenty of farms a D 7007 from the 07 series still pulls the trailer or the muck spreader. To keep it that way there are more than 200 parts for this model, from GRANIT, LUK, HELLA, Bosch/Rexroth and VICTOR REINZ.

Brakes, steering and clutch

For the brakes you will find brake shoes and the matching return springs. Always fit new springs with new shoes. A spring that has been heat cycled for years loses tension and lets the shoe drag lightly on the drum, which shows up as a warm drum after a run on the road.

On the steering side there are ball joints and a bolt set for the steering valve. If the steering has play, have someone rock the wheel back and forth while you feel each joint by hand. That quickly tells you which one is worn. Use a fresh split pin every time you refit a joint.

For the clutch there are clutch plates and thrust bearings, including a sealed release bearing for the main clutch.

Engine and fuel system

Around the Deutz engine there are crankshaft seals, sealing rings and shims. On the exhaust side you will find exhaust manifolds and gaskets. Old manifold studs and nuts often come off with half the rust attached, so use new fixings and a new gasket, or the joint will be blowing again within weeks.

In the fuel system, a repair set for the feed pump helps when the engine is slow to fire or needs lengthy bleeding after standing. A lockable tank cap with a vent is also available.

For the electrics there are starter motors and alternators. A sluggish starter is not always at fault itself, so check the battery terminals and the earth connection first.

Working out what you need

On a tractor of this age, something has usually been replaced along the way. That makes it worth laying the old part next to the new one. A number stamped into or printed on the part is the quickest point of comparison. The tractor type plate gives the model and chassis number, which help when you are choosing between two versions of a clutch plate or starter.

These Deutz tractors from the same 07 series have their own pages too:

Useful when there is more than one classic in the yard. Newer and other models are under Deutz-Fahr parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart