Menu
EUR

Valtra A 75 tractor parts & technical data

More than 100 parts for the Valtra A 75 from the A series on one page, from trailer couplings and electrics to steering and front axle components.

101 parts found for Valtra-Valmet A 75
Show:
Door lock, right Fendt Farmer 240 S (Typ 294), GT 395
€54,33 €44,90 €51,60 €42,64
You save 5%
BOSCH Sensor hydraulic pressure lifting height
BOSCH
Version: Lifting height. More
Version: Lifting height.
€355,33 €293,66 €314,26 €259,72
You save 12%
MAHLE Alternator 14 V, 65 A, pulley-Ø 80 mm, form A
MAHLE
Pulley Ø (mm): 80.0 | Charging current (A): 65 | Form: A | Pulley spacing (mm): 37,0 | Nominal values (V / A): 14 / 65 | Mounting L / d / R (mm): 82,... More
Pulley Ø (mm): 80.0 | Charging current (A): 65 | Form: A | Pulley spa...
€224,58 €185,60 €140,35 €115,99
You save 38%
DANA Spicer Spacer as front axle 745, outer-Ø 150 mm, inner-Ø 120 mm, 1 mm
DANA Spicer
Thickness (mm): 1 | Outer Ø (mm): 150 | Inner Ø (mm): 120 More
Thickness (mm): 1 | Outer Ø (mm): 150 | Inner Ø (mm): 120
€44,85 €37,07 €42,60 €35,21
You save 5%
Thermostat Ø 67 mm, 83 °C Massey Ferguson, Case IH, Steyr
Ø: 67 mm. Temperature: 83 °C. More
Ø: 67 mm. Temperature: 83 °C.
€36,87 €30,47 €35,00 €28,93
You save 5%
Crankshaft seal for Ø 58 x 80 x 12 mm Massey Ferguson
Outer Ø: 80 mm. Width: 12 mm. Inner Ø: 58 mm. More
Outer Ø: 80 mm. Width: 12 mm. Inner Ø: 58 mm.
€14,80 €12,23
GRANIT Cylinder head gasket engine Sisu
€79,42 €65,64 €75,40 €62,31
You save 5%
GRANIT Cylinder head gasket set upper Case IH, Valtra-Valmet, Steyr engine Sisu 320D
€180,60 €149,26 €171,55 €141,78
You save 5%
GRANIT Oil pressure switch engine and transmission M10 x 1, 0,15 - 0,45 bar
GRANIT
Version: Thread: M10 x 1 cylindrical, Switching pressure: 0.15 - 0.45 bar, Blade terminal 6.3 mm, AF: 24 mm, Colour: white. Connection: Blade terminal... More
Version: Thread: M10 x 1 cylindrical, Switching pressure: 0.15 - 0.45 ...
€26,20 €21,65
FLEETGUARD Hydraulic oil filter HF35322
€99,05 €81,86 €89,60 €74,05
You save 10%
Scharmüller Drawbar frame standard 76,4 kN, 330 mm, type 427, axle tube Ø 120 mm
Scharmüller
Category: Bearing supports | Colour: Black | Description: compatible with Q37 Daimler end cross member or Scharmüller item 34.437.001.0 Suitable for ... More
Category: Bearing supports | Colour: Black | Description: compatible w...
€5.043,00 €4.167,77
DANA Spicer Plug front axle 745
€19,40 €16,03
GRANIT Ball joint left 5 notches taper 16,2 - 18,3 mm, 310 mm, M14 x 1,5
GRANIT
A: 310 mm. C: M14 x 1,5 mm. D: 18 mm. E: 16,2 mm. F: 18,3 mm. Taper: 16,2 - 18,3 mm. More
A: 310 mm. C: M14 x 1,5 mm. D: 18 mm. E: 16,2 mm. F: 18,3 mm. Taper: 1...
€76,34 €63,09 €72,50 €59,92
You save 5%
Engine preheater, complete connection Ø 40 mm, press
Connection: Ø 40 mm press fitting. More
Connection: Ø 40 mm press fitting.
€398,22 €329,11 €378,30 €312,64
You save 5%
Connecting rod bolt TX star 58 mm Valtra-Valmet engine Sisu 320-634
Feed pump 5 hole, hole spacing 25/37 and 45 mm, flange 52 mm
Version: 5 holes, Vertical hole spacing: 25/37 mm, Horizontal hole spacing: 45 mm, Flange to lever end: 52 mm. Menke no.: 209000. More
Version: 5 holes, Vertical hole spacing: 25/37 mm, Horizontal hole spa...
€42,99 €35,53 €40,80 €33,72
You save 5%
Intake manifold gasket Massey Ferguson, Case IH, Steyr, New Holland
GRANIT Door lock, left Fendt Farmer 240 S (Typ 294), GT 395
€56,94 €47,06 €54,00 €44,63
You save 5%
Showing 25 - 48 of 101

Valtra A 75 parts

The Valtra A 75 is a tractor most owners still service themselves, and the parts on this page reflect that kind of work. More than 100 of them fit this model, from GRANIT and from manufacturers such as DANA Spicer, Walterscheid, Scharmüller and GRAMMER.

Cooling and engine

Water pumps are listed together with their gaskets. On the engine side there are valve cover gaskets, seals for the valve cover, crankshaft seals, O-rings for the feed pump and a gasket between the exhaust silencer and the turbocharger. Alternators complete this group.

When a crankshaft seal starts to weep, look closely at the shaft before fitting the new one. If the old lip has worn a groove into the running surface, a new seal sitting in that same groove will not last. Drive the new seal in square with a suitable drift, oil the lip lightly and make sure it does not fold back on fitting. For the water pump, a new gasket and fresh coolant go with every replacement, and the system needs bleeding with the engine warm.

Hitch, steering, cab and lights

  • Drawbar frames and drawbars with ball, from makers including Scharmüller and Walterscheid.
  • Ball joints for the steering linkage.
  • Door locks and tractor seats, with GRAMMER among the seat brands.
  • Work lamps, indicator and position lights and flasher units.

If the battery is not charging properly, the alternator is not automatically to blame. Measure the charging voltage with the engine running and check the belt, the earth strap and the plug connections first. And when a tractor seat sags or rocks, the cause usually sits in the suspension or the slide rails underneath rather than in the cushion, so look there before replacing the whole seat.

Getting the right part for your A 75

The A 75 is part of the Valtra A series. Confirm the model on the type plate, then look for a stamped or printed number on the part you are replacing. Water pumps usually carry it on the housing, alternators on a small plate at the back. Door locks, ball joints and lights also come in left and right versions, so note the side before ordering.

Other tractors in the A series have their own pages, which saves time if your fleet includes more than one of them:

For any other model of the brand, start at Valtra parts, where every type with replacement parts available is listed.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart