Menu
EUR

Valtra N 134 tractor parts & technical data

More than 60 matching parts for the Valtra N 134 from the N4 series, including trailer couplings, electrics and brake and transmission parts, neatly grouped.

61 parts found for Valtra-Valmet N 134
Show:
AdBlue injection unit Valtra-Valmet, Fendt
€717,52 €592,99 €660,12 €545,55
You save 8%
Scharmüller Drawbar K50 Cramer, rail 335 mm, pin Ø 22 mm, 31 kN
Scharmüller
Rail width: 335 mm. Guide width: 30 mm. Detent pin Ø: 22 mm. Load capacity: 250 kg. D-value: 31 kN. Overhang: 148 mm. Plate height: 150 mm. Hole: M20... More
Rail width: 335 mm. Guide width: 30 mm. Detent pin Ø: 22 mm. Load cap...
€899,63 €743,50 €871,22 €720,02
You save 3%
Walterscheid Piton Fix rail width 330 mm, locking pin Ø 25 mm, 3000 kg, 89,3 kN
Walterscheid
Rail width: 330 mm. Detent pin Ø: 25 mm. Guide width: 32 mm. Load capacity: 3000 kg. D-value: 89.3 kN. Colour: Black. Description: This product is a ... More
Rail width: 330 mm. Detent pin Ø: 25 mm. Guide width: 32 mm. Load cap...
€1.748,75 €1.445,25 €1.382,58 €1.142,63
You save 21%
Scharmüller Drawbar ball 50 rail 335 mm, pin Ø 22 mm, 250 kg, AGCO gray
Scharmüller
Rail width: 335 mm. Guide width: 30 mm. Detent pin Ø: 22 mm. Load capacity: 250 kg. D-value: 31 kN. Overhang: 168 mm. Plate height: 150 mm. Hole: M20... More
Rail width: 335 mm. Guide width: 30 mm. Detent pin Ø: 22 mm. Load cap...
€839,65 €693,93 €812,85 €671,77
You save 3%
Scharmüller Forced steering inner part left Ball 80 to K50 250 mm, 2 ton
Scharmüller
Assembly notes: Anticlockwise. Steering power: 2 t. Lock: K50. Description: Approved for steering forces up to 20 kN (2 t). Load capacity: 2 t. Load c... More
Assembly notes: Anticlockwise. Steering power: 2 t. Lock: K50. Descrip...
€481,06 €397,57 €453,50 €374,79
You save 6%
Scharmüller Support plates ball 80, 3000 kg, 670 x 280 mm, thickness 50 mm Valtra
Scharmüller
suitable for: Valtra. Series: N5-Serie. Category: Support plates. Version: Standard. Thickness: 50 mm. Colour: AGCO grey. Width: 280 mm. D-value: 89,3... More
suitable for: Valtra. Series: N5-Serie. Category: Support plates. Vers...
€1.771,48 €1.464,03 €1.583,40 €1.308,60
You save 11%
Starter ring gear Ø 405/373 mm, 133 teeth Valtra-Valmet
Version: Ø 405/373 mm, 133 teeth. More
Version: Ø 405/373 mm, 133 teeth.
€224,52 €185,55 €206,56 €170,71
You save 8%
Belt tensioner Ø 75 mm, width 46,5 mm, Massey Ferguson and Fendt
Outer Ø: 75 mm. Width: 46,5 mm. More
Outer Ø: 75 mm. Width: 46,5 mm.
€117,22 €96,88
Thermostat Ø 67 mm, 83 °C Fendt, Massey Ferguson
Ø: 67 mm. Temperature: 83 °C. More
Ø: 67 mm. Temperature: 83 °C.
€39,96 €33,03
Temperature sensor A84-A134
€94,76 €78,31 €87,18 €72,05
You save 8%
Showing 49 - 61 of 61

Valtra N 134 parts for the hitch, cooling system and exhaust

The rear end of a Valtra N 134 takes a beating. That is where the pick-up hitch hangs, where the ball carries the weight of the trailer drawbar and where the rods of a self-steering trailer axle are connected. This page brings together more than 60 new parts that fit the N 134, and a good share of them deal with hitching. Alongside those you will find cooling system parts, engine and exhaust sensors and a rear-view mirror for the cab.

Hitching gear from drawbar frame to screw-on ball adapter

For the hitch there are drawbar balls, loose balls, a ball hitch, screw-on ball adapters and inserts for the pick-up hitch. If you pull a trailer with forced steering, the forced steering parts are here too, such as an insert that the steering rod of the trailer locks into. To fix all of this to the tractor you can choose from support plates, adapter plates and drawbar frames, and the Piton Fix suits anyone who prefers a fixed pin. These parts come from makers such as Scharmüller and Walterscheid as well as GRANIT.

A workshop tip: after swapping an insert in the pick-up hitch, always check that the latch has dropped fully home before you pull away. A ball that has worn oval or stepped is worth replacing early. Play at that point shows up as a knock every time you pull off or brake, and the knock travels straight into the drawbar and chassis of the trailer.

Cooling, sensors and seals

Under the bonnet you will find radiator hoses, including the bottom hose on the radiator, temperature sensors and NOX sensors for the exhaust. Seals for the pressure pipe are listed as well. Wabco and SACHS are also among the makers supplying this tractor. When you replace a radiator hose, check the clamps and the stubs it slides onto. A hose that has gone soft or cracked on the inside often looks fine from the outside, and a new hose on a pitted stub will keep weeping.

Matching the right part to your N 134

Start at the type plate on the tractor and note the exact model. Once the old part is off, look for a stamped or printed reference number and compare it with the details shown for the product. For hitch parts, also check which system is fitted now, because a ball, a pin and a hitch insert are each mounted in a different way.

Within the Valtra N4 range, the N 134 is one of several tractors. Each of the other tractors in that range has its own page showing only the parts that fit it, which helps when there is more than one Valtra in the yard:

For every other model of the make, go to Valtra parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison
This product has been added to your cart