Menu
EUR

Valtra N 163 tractor parts & technical data

Valtra N 163 owners will find more than 100 parts for this N3 series tractor here, including trailer couplings, electrics and lighting.

107 parts found for Valtra-Valmet N 163
Show:
Thermostat Ø 67 mm, 83 °C Fendt, Massey Ferguson
Ø: 67 mm. Temperature: 83 °C. More
Ø: 67 mm. Temperature: 83 °C.
€39,96 €33,03
Door lock, right Massey Ferguson, Case IH, Steyr
€49,57 €40,97 €45,60 €37,69
You save 8%
Starter switch with 2 keys
€73,12 €60,43 €67,27 €55,60
You save 8%
Cobo Headlight left / right 12 V, built-in, screw fixing
Cobo
Nominal voltage: 12 V. Installation location: Left, right. Bulb: 12V55W / H4, 12V4WK / T4W. Bulbs included: No. Light function: Dipped beam, full beam... More
Nominal voltage: 12 V. Installation location: Left, right. Bulb: 12V55...
€100,76 €83,27 €92,70 €76,61
You save 8%
Oil drain valve M18 x 1,5
Thread: M18 x 1.5. More
Thread: M18 x 1.5.
€68,16 €56,33 €62,71 €51,82
You save 8%
Main bearing standard Ø 85 mm
€50,48 €41,72 €46,44 €38,38
You save 8%
Temperature sensor for common rail systems Sisu-engines
Version: For common rail systems, to fit Sisu engines. More
Version: For common rail systems, to fit Sisu engines.
€174,05 €143,84 €160,13 €132,34
You save 8%
Showing 97 - 107 of 107

Valtra N 163 parts

On this page you can order more than 100 new replacement parts for the Valtra N 163, from GRANIT, Scharmüller, DANA Spicer, Walterscheid, BOSCH and other makers. They fall into three groups: the cooling system, the hitch and cab, and the engine.

Cooling system

There are thermostats, temperature sensors, fan clutches and electric cooling fans. A slipping fan clutch lets the fan turn too slowly, and the temperature climbs under heavy load. With the engine off and cold, the fan should feel stiff when you turn it by hand. If it spins freely and keeps turning, the clutch is due for replacement. A thermostat always goes in with a new seal, after which the cooling system needs bleeding.

Hitch, cab and engine

  • Ball drawbars, ball inserts, drawbar frames and adapter plates.
  • Door locks, work lamps and the turbo for the cab.
  • Reman turbochargers, gear reduction starters and clutch sets.
  • Seals such as the pressure pipe seal, and O-rings including the oil filler cap ring.

Grease the ball on a ball hitch and check its diameter now and then. Replace the insert before the towing eye starts to knock every time you pull away.

Matching parts to your tractor

The identification plate confirms that the tractor is an N 163, and the reference number on the old part is the quickest route to the right replacement. For a ball drawbar, measure the rail width and the pin before ordering.

Door locks, work lamps and the turbo

A door lock that no longer catches is a small job with a big effect on a long day in the cab. Remove the door trim, unhook the rods from the old lock and note how they were fitted. Grease the new lock lightly and adjust the striker on the pillar until the door shuts with a normal push. Before replacing a work lamp that flickers, check the plug and the cable, as a corroded contact is a common cause.

With a turbocharger, oil supply is everything. Renew or thoroughly clean the oil feed pipe, prime the turbo with clean engine oil before the first start and let the engine idle for a while. After heavy work, leave the engine running for a minute before switching off so the turbo can cool.

Other N models

The Valtra N 103, Valtra N 113, Valtra N 123 and Valtra N 143 from the same range have their own pages. Check each tractor individually. All Valtra models are listed under Valtra parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison
This product has been added to your cart