Menu
EUR

Valtra 8400 tractor parts & technical data

Also known as the Valmet 8400: for the Valtra 8400 this page lists more than 170 parts such as steering and front axle, electrics and trailer couplings.

157 parts found for Valtra-Valmet 8400
Show:
Aircon compressor 12 V, pulley Ø 132 mm, 2 grooves, 135 ccm oil
Reference no.: QP7H15-8024 | Suitable oil: PAG 46 | For compressor: 7H15 | Nominal voltage (V): 12 | Pulley Ø (mm): 132 | Fixing: EM | Oil quantity (... More
Reference no.: QP7H15-8024 | Suitable oil: PAG 46 | For compressor: 7H...
€357,93 €295,81 €329,30 €272,15
You save 8%
Ball joint 260 mm, taper 24 - 26 mm, M20 x 1,5 / M24 x 1,5
A: 260 mm. C: M20 x 1,5 mm. D: M24 x 1,5 mm. E: 24 mm. F: 26 mm. Taper: 24 - 26 mm. More
A: 260 mm. C: M20 x 1,5 mm. D: M24 x 1,5 mm. E: 24 mm. F: 26 mm. Taper...
€82,15 €67,89 €75,58 €62,46
You save 8%
Ball joint 295 mm, M24 x 1,5, M22 x 1,5, taper 29 - 32,2 mm
A: 295 mm. C: M24 x 1,5 mm. D: M22 x 1,5 mm. E: 29 mm. F: 32,2 mm. Taper: 29 - 32,2 mm. More
A: 295 mm. C: M24 x 1,5 mm. D: M22 x 1,5 mm. E: 29 mm. F: 32,2 mm. Tap...
€103,69 €85,69 €95,39 €78,84
You save 8%
Repair set water pump Valtra-Valmet Mezzo 6900, Mega 8000-8400
€150,77 €124,60 €138,71 €114,64
You save 8%
Injection nozzle Case IH CS 100-150, Steyr 9105-9145, Valtra-Valmet
Type formula: ADB145M34447. More
Type formula: ADB145M34447.
€40,71 €33,64 €37,45 €30,95
You save 8%
Glow plug 12 V, 15,5 A, thread 7/8 inch - 14 UNF
Version: 12 V, 15.5 A, thread 7/8" - 14 UNF. More
Version: 12 V, 15.5 A, thread 7/8" - 14 UNF.
€33,85 €27,98
Gasket set top and bottom engine Sisu 620, 634 Valtra T 120-190
€544,68 €450,15 €501,11 €414,14
You save 8%
Reman turbocharger Case IH, Steyr, Valtra-Valmet, Massey Ferguson
€2.163,70 €1.788,18 €2.073,50 €1.713,64
You save 4%
Door lock, left Massey Ferguson, Case IH, Steyr
€49,57 €40,97 €45,60 €37,69
You save 8%
Scharmüller Drawbar K80 manual, rail 335 mm, pin Ø 22 mm, 3000 kg, AGCO gray
Scharmüller
Rail width: 335 mm. Detent pin Ø: 22 mm. Guide width: 30 mm. Load capacity: 3000 kg. D-value: 89,3 kN. Plate height: 150 mm. Colour: AGCO grey. Overh... More
Rail width: 335 mm. Detent pin Ø: 22 mm. Guide width: 30 mm. Load cap...
€1.349,76 €1.115,50 €1.183,18 €977,84
You save 12%
Stop cable 2015 / 2250 mm Valtra-Valmet 205-905, 6000-8750
To fit as: Valtra - Valmet 205, 305, 365, 405, 465, 505, 600, 605, 665, 700, 705, 805, 865, 900, 905, 6000, 6100, 6300, 6400, 6600, 6800, 8000, 8100, ... More
To fit as: Valtra - Valmet 205, 305, 365, 405, 465, 505, 600, 605, 665...
€34,18 €28,24
Internal plate PTO clutch Ø 133,4 x 93 mm, 1,8 mm, 45 teeth
Version: Thickness: 1.8 mm, inner: 93 mm, outer: 133.4 mm, 45 splines More
Version: Thickness: 1.8 mm, inner: 93 mm, outer: 133.4 mm, 45 splines
€23,45 €19,38
Ball joint 210 mm, M22 x 1,5 mm, M24 x 1,5 mm
A: 210 mm. C: M22 x 1,5 mm. D: M24 x 1,5 mm. More
A: 210 mm. C: M22 x 1,5 mm. D: M24 x 1,5 mm.
€62,32 €51,50 €57,33 €47,38
You save 8%
Thermostat Ø 67 mm, 83 °C Massey Ferguson, Case IH, Steyr
Ø: 67 mm. Temperature: 83 °C. More
Ø: 67 mm. Temperature: 83 °C.
€38,47 €31,79 €35,39 €29,25
You save 8%
Injection nozzle engine 620DSL, 612DS Valtra, Massey Ferguson
€224,74 €185,74 €206,76 €170,88
You save 8%
Stop cable A 1490 mm, B 1400 mm Valtra-Valmet Mega 8000-8400
A: 1490 mm. B: 1400 mm. More
A: 1490 mm. B: 1400 mm.
€40,03 €33,08 €36,83 €30,44
You save 8%
Cylinder head bolt 12 x 140 mm Massey Ferguson, Case IH, Steyr
Dimensions: M12 x 140 mm. More
Dimensions: M12 x 140 mm.
€15,23 €12,58
Connecting rod bolt 85 mm Valtra-Valmet, Case IH, Steyr
Dimensions: 85 mm long. More
Dimensions: 85 mm long.
€42,51 €35,13 €39,11 €32,32
You save 8%
Cylinder head gasket set upper Case IH, Steyr, New Holland
€231,31 €191,17 €212,81 €175,87
You save 8%
Door lock, left Fendt Farmer 240 S (Typ 294), GT 395
€59,42 €49,11 €54,67 €45,18
You save 8%
Oil pressure switch engine and transmission M10 x 1, 0,15 - 0,45 bar
Version: Thread: M10 x 1 cylindrical, Switching pressure: 0.15 - 0.45 bar, Blade terminal 6.3 mm, AF: 24 mm, Colour: white. Connection: Blade terminal... More
Version: Thread: M10 x 1 cylindrical, Switching pressure: 0.15 - 0.45 ...
€27,39 €22,63
BOSCH Sensor hydraulic pressure lifting height
BOSCH
Version: Lifting height. More
Version: Lifting height.
€370,79 €306,44 €314,26 €259,72
You save 15%
Seal kit hydraulic steering
€226,79 €187,43 €208,65 €172,44
You save 8%
Repair set brake cylinder Valtra-Valmet, Fendt
€39,37 €32,54 €36,22 €29,93
You save 8%
Feed pump 3 hole, hole spacing 52 x 34 mm, flange 23 mm
Version: 3 holes, Vertical hole spacing: 52 mm, Horizontal hole spacing: 34 mm, Flange to lever end: 23 mm. More
Version: 3 holes, Vertical hole spacing: 52 mm, Horizontal hole spacin...
€121,09 €100,07 €111,40 €92,07
You save 8%
Borg Warner Fan clutch Ø 600 mm Valtra-Valmet Mega 8400-8750
€262,50 €216,94 €250,92 €207,37
You save 4%
Borg Warner Cooling fan Ø 600 mm Valtra-Valmet Mega 8400-8750, T 120 - T 191
€231,44 €191,27 €194,69 €160,90
You save 16%
Water pump without gasket Valtra-Valmet, Massey Ferguson
€255,91 €211,50 €235,44 €194,58
You save 8%
Thermostat Ø 54 mm, 79 °C
Ø: 54 mm. Temperature: 79 °C. More
Ø: 54 mm. Temperature: 79 °C.
€19,81 €16,37
Thermostat Ø 67 mm, 83 °C
Ø: 67 mm. Temperature: 83 °C. More
Ø: 67 mm. Temperature: 83 °C.
€39,55 €32,69 €36,39 €30,07
You save 8%
Optibelt V-belt Massey Ferguson 3120, 5425-5460, 6180, 6445, 6455
€36,11 €29,84 €33,22 €27,46
You save 8%
Feed pump 5 hole, hole spacing 25/37 and 45 mm, flange 52 mm
Version: 5 holes, Vertical hole spacing: 25/37 mm, Horizontal hole spacing: 45 mm, Flange to lever end: 52 mm. Menke no.: 209000. More
Version: 5 holes, Vertical hole spacing: 25/37 mm, Horizontal hole spa...
€44,86 €37,07 €41,27 €34,11
You save 8%
O-clamp set 115 x 3,5 mm Steyr, Massey Ferguson - 3 pieces
Dimensions: All rings 115 x 3.5 mm. More
Dimensions: All rings 115 x 3.5 mm.
€35,00 €28,93 €32,20 €26,61
You save 8%
Door lock, right Fendt Farmer 240 S (Typ 294), GT 395
€56,69 €46,85 €52,15 €43,10
You save 8%
Lift rod Valtra Mezzo 6000-6900, Mega 8000-8550
€273,87 €226,34 €251,96 €208,23
You save 8%
Scharmüller Ball 80® ball inserts gray cast iron, rail width 335 mm, 4000 kg
Scharmüller
Rail width: 335 mm. Detent pin Ø: 22 mm. Guide width: 30 mm. Load capacity: 4000 kg. D-value: 89,3 kN. Plate height: 160 mm. Colour: AGCO grey. Overh... More
Rail width: 335 mm. Detent pin Ø: 22 mm. Guide width: 30 mm. Load cap...
€1.116,48 €922,71
Seal kit Valtra-Valmet C 90 - 150, M 120-150, T 120-190
€90,76 €75,01 €83,50 €69,01
You save 8%
Indicator/position light yellow, white, 170 x 63,5 x 60,3 mm, left / right
Bulb: 12V21WK / P21W, 12V5WK / R5W. Colour: Yellow, white. Width: 170 mm. Form: Rectangular. Height: 53,5 mm. Dimensions W x H x D: 170 x 63,5 x 60,3 ... More
Bulb: 12V21WK / P21W, 12V5WK / R5W. Colour: Yellow, white. Width: 170 ...
€34,72 €28,69 €31,94 €26,40
You save 8%
HELLA Headlight left / right 12 / 24 V, H4, glass 164 x 103 mm, built-in Fendt
HELLA
Bulb: 12V60/55W / H4, 12V4WK / T4W, 24V75/70W / H4, 24V4WK / T4W. Fixing: 3-point mounting. Installation location: Left/right. Nominal voltage: 12 / 2... More
Bulb: 12V60/55W / H4, 12V4WK / T4W, 24V75/70W / H4, 24V4WK / T4W. Fixi...
€107,20 €88,60 €103,23 €85,32
You save 4%
Seal kit hydraulic steering
€353,13 €291,84 €324,88 €268,50
You save 8%
Showing 49 - 96 of 157

Valtra 8400 parts, also known as the Valmet 8400

Plenty of farmers still call it the Valmet 8400, while other paperwork says Valtra. Either way it is the same tractor from the Mega range, and there are more than 170 parts for it on this page, from makers including GRANIT, Scharmüller, GRAMMER, Walterscheid and DANA Spicer.

Keeping the engine healthy

Under the bonnet you will find radiator hoses such as the top hose, thermostats with their gasket, alternators and seal kits. If the engine will not reach temperature in winter or runs hot under heavy load, the thermostat is often the first suspect. There are also stop cables for shutting the engine down, seals like the one for the feed pump, O-rings for the differential and repair kits.

Clutch, steering and the cab

  • A clutch plate made for the Valtra-Valmet
  • Ball joints for the steering
  • An air suspended tractor seat
  • Door locks and a flasher unit for the indicators
  • Ball type drawbars at the rear

The stop cable is one of those parts nobody thinks about until it snaps. If the engine is reluctant to shut off or the handle has to come out further each time, the inner cable is stretching or binding in its outer. Route a new one without tight bends and well away from the hot exhaust manifold, or the same story starts over again soon enough. A few drops of light oil down the outer keep it moving freely.

Thermostat check before you swap

You can test a thermostat in a pan of water on the stove with a thermometer beside it. It should start opening around its rated temperature and close again as the water cools. When refitting, always use a new gasket and, if there is a small bleed hole, put it at the top. Refill the cooling system slowly and let the engine warm up with the heater valve open so trapped air can escape, then check the level once more after the first run.

Valtra or Valmet, the number is what counts

Because the same tractor goes by two names, rely on the number on the type plate. If it says 8400, this is the right page. For a clutch plate, compare the diameter and the number of splines, and for a stop cable the length of the cable itself. If a reference number is still readable on the old part, use it as a check.

Within the Mega range these models each have their own page, useful when a second Valtra shares the yard: the Valtra 8050, the Valtra 8150 and the Valtra 8550. Other models from the brand, older Valmet tractors included, are under Valtra parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison
This product has been added to your cart