Menu
EUR

Valtra T 154 tractor parts & technical data

Brakes, transmission, electrics or a trailer coupling for the Valtra T 154: this page covers the T4 series with more than 60 parts to pick from.

62 parts found for Valtra-Valmet T 154
Show:
Starter ring gear Ø 405/373 mm, 133 teeth Valtra-Valmet
Version: Ø 405/373 mm, 133 teeth. More
Version: Ø 405/373 mm, 133 teeth.
€215,16 €177,82 €204,40 €168,93
You save 5%
Belt tensioner Ø 75 mm, width 46,5 mm Fendt, Massey Ferguson
Outer Ø: 75 mm. Width: 46,5 mm. More
Outer Ø: 75 mm. Width: 46,5 mm.
€130,29 €107,68 €123,75 €102,27
You save 5%
Wabco Solenoid valve 3/2-way, 12 V, 1,41 A, M16 x 1,5, standard closed
Wabco
Eligible: Environmental protection and safety (formerly de minimis) More
Eligible: Environmental protection and safety (formerly de minimis)
€413,58 €341,80 €392,90 €324,71
You save 5%
BOSCH Pressure regulator CP4 Valtra-Valmet, Fendt, Massey Ferguson
€177,02 €146,30 €156,56 €129,39
You save 12%
GRANIT Rail pressure valve Valtra-Valmet N 104 - T 234, Massey Ferguson
€142,86 €118,07 €135,70 €112,15
You save 5%
GRANIT Tensioning pulley Ø 74 / 46,3 mm, PK12
€44,83 €37,05 €42,55 €35,17
You save 5%
GRANIT Signal transmitter exhaust aftertreatment Valtra-Valmet T 144 - T 254
€607,18 €501,80 €576,80 €476,69
You save 5%
Temperature sensor Fendt, Massey Ferguson, Valtra-Valmet
€90,81 €75,05 €86,25 €71,28
You save 5%
GRANIT AdBlue-feed unit Valtra-Valmet A84-A134
GRANIT
Description: AdBlue supply units ensure even metering of AdBlue depending on the load on the common rail engine. It is important that only filtered ur... More
Description: AdBlue supply units ensure even metering of AdBlue depend...
€1.004,11 €829,84 €953,90 €788,35
You save 5%
Rail pressure sensor Fendt 5255L-9470X, Massey Ferguson Series 5600-9530
Scharmüller Forced steering 250 mm, K50, left, 2 ton, black, 4,86 kg
Scharmüller
Steering power (t): 2 | Colour: Black | Lock: K50 | Assembly notes: Anticlockwise | Description: Approved for steering forces up to 20 kN (2 t) | Conn... More
Steering power (t): 2 | Colour: Black | Lock: K50 | Assembly notes: An...
€472,38 €390,40 €417,75 €345,25
You save 12%
GRANIT AdBlue injection unit Valtra-Valmet, Fendt
€687,61 €568,27 €653,20 €539,83
You save 5%
GRANIT Rail pressure sensor Valtra-Valmet, Fendt, Massey Ferguson
€283,02 €233,90 €268,85 €222,19
You save 5%
Gasket manifold for turbocharger 162000110800, 47107834
€31,81 €26,29 €30,20 €24,96
You save 5%
Showing 25 - 48 of 62

Valtra T 154 parts for engine sensors, cooling and hitch

A fault code on the dashboard of a Valtra T 154 often points to one of the many sensors on the engine. This page lists more than 60 replacement parts for the T 154, and that sensor side is well represented, next to cooling, exhaust and hitching parts.

Engine management and cooling

  • temperature sensors
  • a rail pressure sensor for the fuel system
  • a NOx sensor for the exhaust
  • the upper radiator hose and thermostats
  • seals for pressure lines and a gasket for the silencer at the turbocharger
  • a belt tensioner

BOSCH supplies part of the sensor range. Before replacing a sensor, check its plug and wiring. A corroded or loose connector produces the same fault code as a failed sensor and costs far less to put right.

Replacing the radiator hose is a good moment to fit new hose clamps too. Drain the coolant into a clean container so you can see its condition. If it looks brown or cloudy, flush the system before refilling.

Hitch and forced steering

For the rear of the tractor there are drawbars, including a manual ball type, screw ball adapters, inserts for forced steering through the Pick-Up Hitch, support plates and adapter plates. Scharmüller, Walterscheid and GRANIT make these, while Wabco covers the air system. A lockable fuel cap is useful on a tractor that is often left in the field.

A belt tensioner usually announces itself with squealing or rattling before it fails. With the belt off, spin the pulley by hand. If it feels rough or has play, replace it together with the belt.

When renewing the silencer gasket at the turbocharger, soak the nuts and studs in penetrating oil the night before. Seized studs on the hot side snap easily, which turns a short job into a long one.

Remove the NOx sensor with the exhaust cooled down and use a slotted socket so the cable is not damaged. Put a little high temperature paste on the thread of the new sensor unless it already has some.

Making sure it fits

Start with the identification plate on your Valtra for the type and serial number. Sensors often look alike from the outside, so the reference number on the old part is the safest check. For hitch parts, measure the rail and pin first.

Other tractors from the same T range have their own pages:

Older Valmet tractors and the rest of the make can be found under Valtra parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison

This product has been added to your cart