Menu
EUR

Valtra T 194 tractor parts & technical data

Choose from more than 50 parts for the Valtra T 194 from the T4 series, such as trailer couplings, electrics, and brake and transmission parts.

58 parts found for Valtra-Valmet T 194
Show:
AdBlue injection unit Valtra-Valmet, Fendt
€717,52 €592,99 €660,12 €545,55
You save 8%
Scharmüller Forced steering inner part left Ball 80 to K50 250 mm, 2 ton
Scharmüller
Assembly notes: Anticlockwise. Steering power: 2 t. Lock: K50. Description: Approved for steering forces up to 20 kN (2 t). Load capacity: 2 t. Load c... More
Assembly notes: Anticlockwise. Steering power: 2 t. Lock: K50. Descrip...
€481,06 €397,57 €453,50 €374,79
You save 6%
Walterscheid Adapter plate rail width 390 mm, hole pattern 160 x 100 mm, M21
Walterscheid
Rail width: 390 mm. Guide width: 32 mm. Detent pin Ø: 25 mm. Load capacity: 2800 kg. D-value: 89,3 kN. Central hole: 95 mm. Hole pattern: 160 x 100 m... More
Rail width: 390 mm. Guide width: 32 mm. Detent pin Ø: 25 mm. Load cap...
€1.150,89 €951,15 €909,90 €751,99
You save 21%
Scharmüller Support plates ball 80, 3000 kg, 670 x 280 mm, thickness 50 mm Valtra
Scharmüller
suitable for: Valtra. Series: N5-Serie. Category: Support plates. Version: Standard. Thickness: 50 mm. Colour: AGCO grey. Width: 280 mm. D-value: 89,3... More
suitable for: Valtra. Series: N5-Serie. Category: Support plates. Vers...
€1.771,48 €1.464,03 €1.583,40 €1.308,60
You save 11%
Starter ring gear Ø 405/373 mm, 133 teeth Valtra-Valmet
Version: Ø 405/373 mm, 133 teeth. More
Version: Ø 405/373 mm, 133 teeth.
€224,52 €185,55 €206,56 €170,71
You save 8%
Rail pressure valve Valtra-Valmet N 104 - T 234, Massey Ferguson
€149,08 €123,21 €137,15 €113,35
You save 8%
Thermostat Ø 67 mm, 83 °C Fendt, Massey Ferguson
Ø: 67 mm. Temperature: 83 °C. More
Ø: 67 mm. Temperature: 83 °C.
€39,96 €33,03
Thermostat Ø 54 mm, 80 °C Massey Ferguson, Valtra, Fendt, Challenger
Ø: 54 mm. Temperature: 80 °C. More
Ø: 54 mm. Temperature: 80 °C.
€26,13 €21,59
Temperature sensor A84-A134
€94,76 €78,31 €87,18 €72,05
You save 8%
Showing 49 - 58 of 58

Valtra T 194 parts: sensors, cooling and hitching

When a warning light comes on in a T 194, the culprit is surprisingly often a sensor, a hose or a connector rather than the engine itself. That is where this page starts. Altogether there are more than 50 new replacement parts that fit the Valtra T 194, from GRANIT, Scharmüller, Walterscheid, BOSCH and Wabco.

Sensors and engine management

For the engine electronics there are NOX sensors for the exhaust aftertreatment, rail pressure sensors for the fuel system and temperature sensors. Before you replace a NOX sensor, read the fault code and inspect the plug and wiring. The sensor sits close to the hot exhaust, and a connector damaged by heat or moisture throws exactly the same code as a failed sensor. Put a little high temperature copper grease on the thread of the new one so it will come out again next time.

Cooling and the belt drive

Thermostats and radiator hoses, including the top hose, keep the cooling circuit tight. There are also belt tensioners, seals for the pressure line and a lockable fuel cap, useful for a tractor left at the edge of a field overnight. Spin a tensioner pulley by hand when the belt is off. If it feels rough or has play, replace it along with the belt.

Not sure about the thermostat? Hang the old one in a pan of water on the stove. If it has not opened by the time the water boils, it is finished. Always fit a new thermostat seal, and while you are there, check that the top radiator hose still feels firm at the connection.

Hitching at the rear

  • Drawbars with a ball, including manual versions
  • Pick-Up Hitch parts, screw-in ball adapters and support plates
  • Piton Fix hitches and adapter plates
  • Forced steering inserts for steered trailers

A K80 ball hitch lasts longer if you keep the ball clean and lightly greased. Check it with a caliper now and then. Once it has worn oval, the drawbar gets play and knocks every time you pull away.

The serial plate and the rest of the T range

Before ordering, check that the serial plate really says T 194 and note the chassis number. For sensors and thermostats, the reference number on the old part makes matching easy. The other models in this range each have their own page, handy if a second Valtra works on the same farm: Valtra T 144, Valtra T 154, Valtra T 174, Valtra T 214 and Valtra T 234. Running a different Valtra as well? Every model has its own overview on Valtra parts.

Brands
  • View more
Price
Min Max
Close
Choose your language
Choose your currency
€

Recently added

Total incl. tax
€0,00
0
Compare
Start comparison
This product has been added to your cart